Abstract:As a promising strategy to improve the ductility and work-hardening, the generation of bulk metallic glass (BMG) composites embedded with a B2 phase has sparked a great interest. In this study, we systematically explored the influence of annealing parameters on formation of the B2-ZrCo phase and micro-hardness evolution, and thus, we summarized the optimal annealing processes which can maximize the B2-ZrCo phase formation and maintain the glass matrix. We examined the microstructures of those annealed alloys via XRD, SEM plus EDS, DSC, FIB, TEM and Struers Durascan microhardness tester. Firstly, the amorphous alloys of Zr55Co31Al14 and Zr56Co28Al16 with 3 mm in diameter were heated to 753 K and 843/853 K for various times at a heating rate of 20 K/min via DSC and then naturally cooled to room temperature. It is found that for annealed Zr56Co28Al16 alloys, the ZrCoAl phase is the dominant phase regardless of the annealing temperature and time, while for annealed Zr55Co31Al14 alloys, at lower annealing temperature, the ZrCoAl phase is the dominant phase, whereas with increasing of annealing temperature and holding time, the B2-ZrCo phase is the dominant phase. In order to further understand the influence of annealing temperature on B2-ZrCo phase formation, we transiently heated those two amorphous alloys to 923 K and then naturally cooled to room temperature within DSC. It is found that the B2-ZrCo phase is still the dominant phase for annealed Zr55Co31Al14 alloy, while the ZrCoAl phase is still the dominant phase for annealed Zr56Co28Al16 alloy. However, the conventional annealing processes have notable disadvantages and significantly limit the retaining of amorphous matrix content due to its low heating rate. Based on the above analysis, the amorphous Zr55Co31Al14 alloy is a promising candidate to fabricate the Zr-Co-Al BMG composite incorporating high volume fraction of B2-ZrCo phase. The flash annealing was used to transiently heat the glassy Zr55Co31Al14 alloy at a heating rate of 1, 5 and 15 K/s via Gleeble. It is found that higher heating rate like 15 K/s can selectively promote formation of the B2-ZrCo phase and suppress the ZrCoAl phase and maintain a large volume fraction of amorphous content. As for the evolution of micro-hardness, we found that for all annealing conditions, the micro-hardness increases first and then decrease, and the micro-hardness of annealed Zr56Co28Al16 alloy is higher than that of annealed Zr55Co31Al14 alloy. The mixing enthalpy between the Zr-Al benefits the formation of a highly dense random packed structure which enhances the micro-hardness. The mechanism of micro-hardness evolution has been discussed in terms of volume fraction and types of crystalline phases, annihilation of free volume, transformation-induced hardening. (C) 2020 Published by Elsevier B.V.

Evolution of B19’ phase during annealing and its influence on the mechanical properties of Zr45Cu45Al10 metallic glass composites

Structural transformation and rheological processes in bulk metallic glass Zr41Ti14Cu12.5Ni10Be22.5

Strain-induced structural evolution of interphase interfaces in CuZr-based metallic-glass composite reinforced by B2 crystalline phase

Microstructure and mechanical properties of Zr46Cu46Al8 bulk metallic glass after annealing treatment

Incorporation of ultrafine nanograins in Zr–Cu–Al–Ni–Co bulk metallic glass enabling significantly improved mechanical properties

Formation of the B2–ZrCo Phase and Micro-Hardness Evolution in Zr–Co–Al BMGs Via Conventional and Flash Annealing

In situ high-energy X-ray diffraction study of thermally-activated martensitic transformation far below room temperature in CuZr-based bulk metallic glass composites

Effects of Crystallization Fractions on Mechanical Properties of Zr-based Metallic Glass Matrix Composites

Change in free volume during the homogeneous flow of Zr-based bulk metallic glass matrix composite

Thermal modification of ZrCu metallic glass nanolaminates: Structure and mechanical properties

Crystallization Behavior and Mechanical Properties of Cu-based Bulk Metallic Glass Composites

Temperature-dependent deformation behavior of a CuZr-based bulk metallic glass composite

Microstructural evolution and analysis of Zr–Co/Cu–Al glassy composites and crystallized alloys via indentation and MD simulations

High-pressure annealing driven nanocrystal formation in Zr50Cu40Al10 metallic glass and strength increase

Deformation-induced microstructural heterogeneity and rejuvenation in a Zr-based bulk metallic glass

An in Situ Neutron Diffraction Study of Plastic Deformation in a Cu46.5Zr46.5Al7 Bulk Metallic Glass Composite

Change of Quasilattice Constant During Amorphous-to-quasicrystalline Phase Transformation in Zr65Al7.5Ni10Cu7.5Ag10 Metallic Glass

Transformation-mediated Plasticity in CuZr based Metallic Glass Composites: A Quantitative Mechanistic Understanding

Isothermal Stability and Selected Mechanical Properties of Zr48Cu36Al8Ag8 Bulk Metallic Glass

Enhancing dynamic mechanical properties of bulk metallic glass composites via deformation-induced martensitic transformation

High temperature deformation behaviors of a CuZr-based bulk metallic glass composite