Abstract:In this study, structural, morphological, thermal and magnetic properties of amorphous-nanocrystalline Fe 70 Cr 10 Nb 10 B 10 (at.%) alloy are discussed. The formation and evaluation of amorphous-nanocrystalline structures of the alloy were followed by XRD, SEM-EDX, TEM, DTA, and VSM techniques. After 50 h of milling Cr, Nb, and B were completely dissolved into the Fe lattice forming 82% of the amorphous phase of the alloy. A gradual dissolution of the alloying elements also increased the lattice parameters concurrently. The lattice parameters reached a maximum value of 2.908 Å after 20 h of milling and then leveled off to a value of 2.891 Å at the end of 50 h of milling. Based on the XRD data, crystallite size and lattice strain of the alloy were calculated as 3.2 nm and 3.34% respectively. TEM analyses revealed that the alloy particulates comprised needle-shaped nanoparticles of an average size of 21 nm. The room temperature magnetic hysteresis loops showed that the increased duration of milling decreased the saturation magnetization from 91 to 24 emu/g. This was mainly due to the upsurge on the amorphous phase content in the alloy as the milling progressed. The increase in amorphous phase content and the subsequent reduction of the saturation magnetization were due to the inter-diffusion of the non-ferromagnetic Cr and B atoms into the Fe lattice. Thermal studies revealed that around 350 °C the amorphous phase of the alloy began crystallizing. The magnetic saturation of the heat-treated alloy also increased with the growth in the crystalline phases. The 50 h milled sample annealed at 700 °C was found to have the highest magnetic anisotropy as observed from the temperature-dependent zero-field cooled and field cooled magnetization measurements. The high-pressure X-ray diffraction measurements revealed that the amorphous state of the alloy remained stable up to 11.3 MPa. It also revealed the structural similarities of the Fe 70 Cr 10 Nb 10 B 10 alloy with those of the Fe 70 M 10 B 20 (M = Nb and Cr) types. For all practical purposes, the microstructural stability under high compressive pressure represents the consolidation properties of the nanostructured magnetic materials since both pressure and temperature-induced phase transformations are the primary controlling factors for the specific magnetization properties of the alloy.

Studies on alloying process of Ni-20Cr-20Fe-0.6Y2O3 powders during mechanical alloying

Mechanical alloying and direct powder forging of Ni–20Cr–20Fe-0.08C alloy

Mechanical alloying of ODS tungsten heavy alloys and microstructure development of intermetallic compounds

Study of the effect of mechanical alloying on the structure of Ni-Mn-Sn Heusler alloy

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Influence of Milling Time on the Microstructure and Soft-Magnetic Properties of Nanocrystalline Fe72Ni8Co8Zr7B4Cu1

Formation and Microstructural Evolution of Ferritic ODS Steel Powders during Mechanical Alloying

Synthesis and characterization of amorphous-nanocrystalline Fe70Cr10Nb10B10 powders by mechanical alloying

Thermal stability and influence of Y2O3 dispersoids on the heat treatment response of an additively manufactured ODS Ni–Cr–Al–Ti γ/γ′ superalloy

Effect of Y2O3 and TiO2 addition of dispersed powder on phase evolution and microstructural analysis of (Al, Cu)3Ti intermetallic synthesised via mechanical alloying and powder metallurgy route

Microstructure development of Y–Ti–O dispersion strengthened Cu alloys fabricated by mechanical alloying

Milling parameter optimization for refinement of NiO/Al mixtures and synthesis of Ni/Al2O3 nanocomposites

Preparation of nanostructural oxide dispersion strengthened (ODS) Mo alloy by mechanical alloying and spark plasma sintering, and its characterization

Effect of Mechanical Alloying on the Microstructure of CoCrNiTiMox High Entropy Alloy

Optimizing the Thermomechanical Process of Nickel-Based ODS Superalloys by an Efficient Method

Effects of Zr, Al, Al+Zr Addition on Phase Evolution Characteristics and Strengthening Mechanisms of Fe‐42Ni‐2Y2O3 ODS Steels Developed by Mechanical Alloying and Spark Plasma Sintering

Magnetic properties and Structural characterization of nanocrystalline Fe-20%A (Ni, Co and Si) alloys powders synthesized by mechanical alloying process

Magnetic and Microstructural Properties of Nanostructured/Amorphous NiTi Prepared by Mechanical Alloying

Structural and thermal properties of the Fe-based alloys prepared by mechanical milling

Achieving ultrahigh strength in oxide-dispersion-strengthened CoCrNi alloy via in situ formation of coherent Y-Ti-O nanoprecipitates

The Optimization of Mechanical Alloying Conditions of Powder for the Preparation of a Fe-10Al-4Cr-4Y2O3 ODS Nanocomposite