Abstract:Highlights • A dual phase β+α Mg-Li alloy was fabricated as reducing the Li content. • The dispersed α-Mg phases mitigate the dimension and distribution of eutectic I-Phase along grain boundaries. • The dual phase Mg-Li alloy exhibits enhanced ductility (elongation (EL) = 17.8 %) due to the improved deformation compatibility. • The continuity of slip between α-Mg and β-Li on plane pairs of {123}Li-{ 112 ̄2 }Mg and {112}Li-{ 112 ̄2 }Mg assures the deformation compatibility across interfaces. • Two strengthening mechanisms, nanoscale B2 (Li, Mg) 3 Zn-type precipitates and the microscale I-phase, are characterized. Mg-Li alloys with high lithium concentrations possess a lightweight body-centered cubic (BCC) matrix structure (β-Li). Interspersed eutectics (primarily the reticulated I-phase) often form along phase boundaries (PBs) and grain boundaries (GBs) which strengthen the alloy but cause the loss of ductility due to the brittle behavior of I-phase. By modifying the Li content, we fabricated the (β+α) biphase Mg-Li alloy in which the α-Mg phase with a hexagonal close-packed structure (HCP) is embedded in β-Li matrix, significantly increasing interface density. The high-density interfaces mitigate the distribution and dimension of the I-phase along GBs and PBs. The alloy exhibits enhanced ductility (elongation (EL) = 17.8 %) compared with the alloy without the α-Mg phase (EL = 5.1 %). Structural characterizations unveil the strengthening mechanism of the nanoscale B2 (Li, Mg) 3 Zn-type precipitates in conjunction with the microscale I-phase. The (Li, Mg) 3 Zn nanophases augment the yield and ultimate tensile strength of the alloy without a discernible compromise in ductility, predominantly due to gliding dislocations cutting through the precipitates. In contrast, the microscale I-phase presents a formidable barrier to dislocation motion, facilitating dislocation pileups at interfaces and culminating in diminished ductility across the interface. In-situ stretching techniques were employed to scrutinize the microstructural evolution of alloys during tensile deformation, elucidating that the deformation compatibility of alloys correlates with the average size of the I-phase and their distribution along GBs and PBs. Corresponding to the orientation relationship (OR) between the α-Mg and β-Li phases {110}Li//{0001}Mg and < 1 ̄11 >Li //< 112 ̄0 >Mg, the slip continuity between α-Mg and β-Li on plane pairs of {123}Li-{ 112 ̄2 }Mg and {112}Li-{ 112 ̄2 }Mg assures the deformation compatibility through facilitating the deformation across interfaces. Simultaneously, during the stretching process, the dispersed I-phase instigates the emergence of sporadic microcracks, indicating gradual damage evolution. These discoveries offer novel insights into achieving exceptional strength-ductility amalgamations in Mg-Li alloys through microstructural adjustments.

Strengthening dual-phase Mg-Li alloy through precipitation control

Enhancing the ductility of cast Mg-Li alloys via dispersed α-Mg phase mitigating the dimension and distribution of interspersed eutectics along grain boundaries

Tailoring the heterophase interfacial structures to improve both strength and ductility of Al-Li alloys by fine tuning major solute Mg

Disclosing Differential Precipitation Behavior of a Novel High Mg-containing Al-Mg-Zn-Si Alloy

Microstructure and Mechanical Properties of Cast Al-Li-Mg Alloy: Role of Cu Addition and Heat Treatment

Influence of Mg content on ageing precipitation behavior of Al-Cu-Li-x alloys

Co-strengthening of the Multi-Phase Precipitation in High-Strength and Toughness Cast Al–Cu–Zn–Mg Alloy Via Changing Zn/Mg Ratios

Balance of Mechanical Properties of Mg-8Li-3Al-2Zn-0.5Y Alloy by Solution and Low-Temperature Aging Treatment

Research and Development of Al-Zn-Mg-Cu-Li Alloys

Achieving Strength and Toughness in Dual-Phase Mg-8Li Alloys Through Phase Structure Control and Composite Fracture

Effective Strategies for Improving the Mechanical Stability of Aged Mg-Li Alloys

New strategy to solve the ambient strength-ductility dilemma in precipitation-strengthened Mg-Gd alloys via Li addition

An investigation on annealing process and strengthening mechanism of cold rolled Mg-10Li-3Al-2.8Zn alloy

Realizing ultra-fine grains and ultra-high strength in conventionally extruded Mg-Ca-Al-Zn-Mn alloys: The multiple roles of nano-precipitations

Microstructure and Mechanical Properties of Mg, Ag and Zn Multi-Microalloyed Al–(3.2–3.8)Cu–(1.0–1.4)Li Alloys

Microstructure and mechanical properties of as-cast ultralight and high strength Mg-10Li-3Al-3Zn-xY alloy with multi-precipitates

Microstructural evolution, precipitation behavior and mechanical properties of a novel Al–Zn–Mg–Cu–Li–Sc–Zr alloy

High Strength and Ductility of Cast Mg-9Gd-1.5Y-0.8Zn-0.3Zr Alloy Achieved by Microstructural Regulation

Enhancing Plasticity in BCC Mg-Li-Al Alloys Through Controlled Precipitation at Grain Boundaries

Strengthening of Mg-Li Alloy Dominated by Continuously Hardened Mg Phase During Room Temperature Rolling

Simultaneous Improvement of Strength, Ductility and Damping Capacity of Single Β-Phase Mg-Li-Al-Zn Alloys