Abstract:<p>This study addresses modeling of aerodynamic damping for a two-dimensional (2-D) suspended circular cylinder in uniform flow, and aims to provide an appropriate model for predicting vortex-induced vibration (VIV) of a circular cylinder. Full-scale and wind-tunnel tests have revealed that the crosswind response of a circular cylinder such as a steel chimney calculated by aerodynamic damping models recommended in several international codes is dramatically overestimated for most cylinders with Scruton numbers less than 15, so these models are re-studied and discussed. This paper proposes an improved aerodynamic damping model that shows good agreement with experimental results. The proposed model is further verified by estimating the transverse displacement responses of suspended circular cylinders tested in uniform flow and the predicted results are promising. The proposed model provides a theoretical basis that can be used to develop an aerodynamic damping model for bridge decks as well as other structures.</p>
What problem does this paper attempt to address?
The problem that this paper attempts to solve is the aerodynamic damping modeling problem of vortex - induced vibration (VIV) of a suspended cylinder in a uniform flow. Specifically, the paper focuses on how to provide an appropriate model to predict the vortex - induced vibration of a two - dimensional suspended cylinder in a uniform flow. It is found that the lateral responses of cylinders such as steel chimneys calculated using the aerodynamic damping models recommended by international codes are significantly overestimated in most cases, especially for cylinders with a Scuton number less than 15. Therefore, these models need to be re - studied and discussed. This paper proposes an improved aerodynamic damping model, which has good consistency with experimental results, and further verifies the effectiveness of this model by estimating the lateral displacement responses of the suspended cylinders tested in a uniform flow. The proposed model provides a theoretical basis for the development of aerodynamic damping models for bridge decks and other structures.
### Main contributions of the paper:
1. **Improved aerodynamic damping model**: An improved aerodynamic damping model is proposed, which can better describe the vortex - induced vibration behavior of a suspended cylinder in a uniform flow.
2. **Experimental verification**: The effectiveness of the model is verified by wind tunnel test data, especially for aerodynamic damping parameters at different wind speeds.
3. **Theoretical basis**: Based on the generalized Van der Pol equation, a new expression for the aerodynamic damping parameter is proposed, which can more accurately reflect the aerodynamic damping characteristics at different wind speeds.
### Formula analysis:
- **Equation of motion**:
\[
M_c \ddot{y}+C_c \dot{y}+K_c y = L
\]
where \(M_c\) is the mass of the cylinder, \(C_c\) is the damping coefficient, \(K_c\) is the stiffness coefficient, \(y\) is the lateral displacement, and \(\dot{y}\) and \(\ddot{y}\) are the lateral velocity and acceleration respectively.
- **Lift force**:
\[
L_b=\frac{1}{2}\rho U^2 C_L D S
\]
\[
L_{ve}=\frac{4\pi f_s\rho D^2}{C_1}K_a(U_r)\left(\frac{\dot{y}}{C_1}S\right)
\]
where \(\rho\) is the air density, \(U\) is the average wind speed, \(C_L\) is the lift coefficient, \(D\) is the cylinder diameter, \(S\) is the cylinder length, \(f_s\) is the natural frequency of the cylinder, \(U_r = \frac{U}{f_s D}\) is the normalized wind speed, and \(K_a(U_r)\) is the aerodynamic damping parameter.
- **Equation of motion in dimensionless form**:
\[
\ddot{Y}+2(\eta_s+\eta_a(U_r))\dot{Y}+Y=\frac{1}{2}\rho D^2 S\left(\frac{1}{2\pi St}\right)^2\frac{U}{U_{cr}}\frac{1}{92}C_L
\]
where \(Y = \frac{y}{D}\), \(\eta_s=\frac{C_c}{2\omega_s M_c}\), \(\eta_a(U_r)=-\frac{\rho D^2 S}{M_c}K_a(U_r)\).
- **Aerodynamic damping parameter**:
\[
K_a(U_r)=K_{a0}(U_r)\left[1 - \frac{\sigma_y^2}{\sigma_{y,L}(U_r)^2}\right]
\]
where \(K_{a0}(U_r)\) is the initial aerodynamic damping parameter, \(\sigma_y\) is the root - mean - square displacement response, and \(\sigma_{y,L}(U_r)\) is the ultimate displacement response when the structural damping is zero.
- **Improved aerodynamic damping parameter**: