Abstract:<math>{101¯2}</math> twins were introduced into the magnesium (Mg) plate AZ31 via pre-rolling along its transverse direction. The plates, both with and without the pre-induced <math>{101¯2}</math> twins, were subjected to uniaxial tension along different directions. Using crystal plasticity modeling, we found that the strengthening effect of the pre-induced <math>{101¯2}</math> twins on the macroscopic flow stress primarily arised from the increased slip resistance caused by the boundaries, rather than the orientation hardening due to the twinning reorientation (although the latter did make its contribution in some specific loading directions). Besides, the pre-existing <math>{101¯2}</math> twins were found, by both experiments and simulation, to promote the activity of prismatic 〈a〉 and pyramidal 〈c + a〉 in the parent matrix of the material. Further analysis showed that the enhanced non-basal slip activity is related to the <math>{101¯2}</math> twin boundaries' low micro Hall-Petch slope ratios of non-basal slips to basal slip. With the critical resolved shear stress (CRSS) obtained from crystal plasticity modeling and the orientation data from EBSD, a probability-based slip transfer model was proposed. The model predicts higher slip transfer probabilities and thus lower strain concentration tendencies at <math>{101¯2}</math> twin boundaries than that at grain boundaries, which agrees with the experimental observation that the strain localization was primarily associated with the latter. The present findings are helpful scientifically, in deepening our understanding of how the pre-induced <math>{101¯2}</math> twins affect the strength and slip activity of Mg alloys, and technologically, in guiding the design of the pre-strain protocol of Mg alloys.

Effects of AlN reinforcement particles on the twinning nucleation and growth in AZ91 alloy

Effect of Adding AlN Ceramic Particles on the Micromorphology of the Mg 17 Al 12 Phase in Magnesium Alloys

Atomistic and Theoretical Insights on Nanoprecipitates-Controlled Strengthening Behavior for Optimum Mechanical Performance in Nanotwinned NiCoCr Alloys

Effect of Al content on the critical resolved shear stress for twin nucleation and growth in Mg alloys

Effect of Al-Nb-Ti-B addition on microstructures, tensile mechanical and damping properties of AZ91 alloy

Atomistic insights into the synergistic effect of nanotwins and nano-precipitates on the mechanical behavior of superalloys

The aging behavior, microstructure and mechanical properties of AlN/AZ91 composite

Effect of AlN on the Mechanical and Electrochemical Properties of Aluminum Metal Matrix Composites

Nucleation Catalysis in Aluminum Alloy A356 Using Nanoscale Inoculants

The Control of Nbb2 Particles in Al-Nbb2 Master Alloy and its Effect on Grain Refinement of Az91 Magnesium Alloy

Effect of Cold and Warm Rolling on the Particle Distribution and Tensile Properties of Heterogeneous Structured AlN/Al Nanocomposites

Silicon Nitride Whisker-Reinforced Aluminum Matrix Composites: Twinning and Precipitation Behavior

Effects of ZrB2 Nanoparticles on the Microstructures and Tensile Properties of a Hot Extruded In Situ AA6111 Composite

Effect of Ti particles on microstructure and mechanical properties of Mg–9Al–1Zn based composite sheets

On the strengthening and slip activity of Mg-3Al-1Zn alloy with pre-induced { 10 1 ̄ 2 } twins

High-Strength Nanotwinned Al Alloys with 9R Phase

Microstructure Elaboration and Mechanical Properties of AlN P /4032al Composite

The effect of the TiC-TiB 2 nanoparticles on the microstructure and mechanical properties of Al-Mn-Si strips fabricated by twin-roll casting

Mechanical and thermal properties of in situ AlN/Al-12Si composite fabricated by laser powder bed fusion

Atomic-scale investigation of the interface precipitation in a TiB2 nanoparticles reinforced Al–Zn–Mg–Cu matrix composite

Micro-alloying effects of Ni on the microstructure and mechanical properties of an Al-Zn-Mg-Cu-Sc-Zr alloy