Abstract:It has been reported that a novel multi-component styrene-butadienestyrene composite (SBSC) modifier composed of the SBS as the main content and additional components including ethyl-vinyl-acetate (EVA), maleic anhydride grafted with ethyl-vinyl-acetate (MAH-g-EVA), naphthenic oil, and antioxidant can be produced by melt blending. This SBSC modifier can be directly mixed with bitumen and aggregate to prepare bitumen mixture, thus thoroughly addressing inferior thermal storage stability of SBS-modified bitumen. However, it is necessary to explore the efficient utilization of the SBSC modifier due to its inadequate engineering application and poor dispersion when the SBSC modifier was added directly to the bitumen mixture. The objective of this research was to investigate the feasibility of using the SBSC modifier to obtain modified bitumen with acceptable thermal storage stability and other enhanced properties. Modified bitumens (SBSC-modified bitumens with 3, 4, 5, 6, 7 % SBSC modifier content, SBS-modified bitumen with 4.5 % SBS modifier content as the control sample) were prepared. The thermal storage stability of modified bitumen was investigated by the segregation test. Besides, the basic physical properties of modified bitumen were tested, including penetration, softening point, and ductility. The rheological properties were evaluated by temperature sweep test, multiple stress creep recovery (MSCR) test, rotational viscosity (RV) test and bending beam rheometer (BBR) test, respectively. Meanwhile, fluorescence microscopy and Fourier transform infrared (FTIR) spectrometer were also applied to characterize the microproperties of the modified bitumen. Results show that the difference in softening point of SBSC-modified bitumens with modifier contents ranging from 3 % to 7 % is less than 2.5 degrees C after 72 h of high temperature storage at 163 degrees C. The softening point and ductility of SBSC-modified bitumen increase considerably with the addition of the SBSC modifier but the decrements of penetration are not significant. Besides, with the increasing addition of the SBSC modifier, complex modulus, average percent recovery, and viscosity of modified bitumen all improve. Meanwhile, phase angle, non-recoverable creep compliance of modified bitumen decrease. The flexural creep stiffness also decreases with the increasing content of the SBS modifier. When the SBS content is the same, the SBSC-modified bitumen gets better thermal storage stability, high and low temperature properties than the SBS-modified bitumen. The microproperties show that the SBSC modifier can be uniformly dispersed in base bitumen and physically mixed with the base bitumen. The SBSC-modified bitumen obtains preferable thermal storage stability. The high and low temperature properties of the bitumen are also enhanced by the addition of the SBSC modifier. Meanwhile, the melt blending method does not restrict the role of the additional components in the SBSC modifier to improve the performance of bitumen. Based on the above findings, it can be considered that the use of SBSC modifier to prepare modified bitumen with enhanced performance is a promising practice. This research may shed light on the application of SBSC modifier to bitumen pavements.

Minireview on the Rejuvenation of Aged Styrene–Butadiene–Styrene (SBS) Modified Bitumen: State-of-the-Art and Outlook

Thermal storage stability and rheological properties of multi-component styrene-butadiene-styrene composite modified bitumen

Comparative Analysis of Rheological and Microscopic Performance of SBS Modified Asphalt Based on Field Aging and Laboratory Aging

Preparation and characterization of active rejuvenated SBS modified bitumen for the sustainable development of high-grade asphalt pavement

Evaluating the Rheological, Chemical and Morphological Properties of SBS Modified Asphalt-Binder under Multiple Aging and Rejuvenation Cycles

Analysis of Rheological Properties and Regeneration Mechanism of Recycled Styrene–Butadiene–Styrene Block Copolymer (SBS) Modified Asphalt Binder Using Different Rejuvenators

Challenges and opportunities in the high-quality rejuvenation of unmodified and SBS modified asphalt mixtures: State of the art

Evaluation of Rheological and Aging Behavior of Modified Asphalt Based on Activation Energy of Viscous Flow

Assessment on Physical and Rheological Properties of Aged SBS Modified Bitumen Containing Rejuvenating Systems of Isocyanate and Epoxy Substances

Development on recycling, aging simulation and regeneration methods of reclaimed styrene-butadiene-styrene modified asphalt

Workability and Rheological Property Evolution of Active Rejuvenated Styrene–Butadiene–Styrene-Modified Bitumen in the Early Stage

Evaluation of Rheological and Microscopic Properties of SBS-Modified Asphalt Binder with Multiple Regeneration

Combined Use of Polyurethane Prepolymer and Aromatic Oil in Physicochemical Rejuvenation of Aged SBS Modified Bitumen for Performance Recovery

Novel Composite Rejuvenators Development and Comparative Analyzes of Epoxy Versus Diisocyanate Rejuvenators in Rejuvenating Aged SBS-Modified Asphalt Binders

Research on Rejuvenation of Styrene-Butadiene-Styrene Block Copolymer Modified Asphalt with Rejuvenating Agent Based on Pre-Mixing Method

Effect of Recycling Agents on Rheological and Micromechanical Properties of SBS-Modified Asphalt Binders

Development of a new rejuvenator for aged SBS modified asphalt binder

Styrene-Butadiene-Styrene polymer modified bitumen: A review on compatibility and physico-chemical properties

Performance Evaluations of Warm-Mix Reaction-Rejuvenated SBS Modified Asphalt Mixtures Incorporated with Wax-Based Additive

Preparation and Macro-Micro Properties of SBS/REOB Modified-Rejuvenated Asphalt

Characterisation of rejuvenation of various modified asphalt binders based on simplified chromatographic techniques