Abstract:A number of methods have been demonstrated to increase the sensitivity of fiber refractometers to changes in the surrounding media refractive index (SMRI). The sensor system is based on the effect of lossy mode resonance (LMR) in a thin multimode fiber with a thin film coating. A chemically resistant thin film of aluminum oxide (Al 2 O 3 ) was applied to the silica surface of an optical fiber by metalorganic chemical vapor deposition (MOCVD). For the first time, the possibility of obtaining aluminum oxide from a vapor-gas mixture of trimethylaluminium - isopropyl alcohol in a hydrogen reducing medium to reduce the carbon content in the sediment has been demonstrated. Using in situ control during the deposition of the coating, the movement of resonances in the transmission spectrum of the optical path was observed. The optical parameters of the deposited coating under various synthesis conditions in the temperature range from 470 to 550 °C were estimated by the movement, shape and depth of several orders of resonances. When creating test sensors, deposition was stopped when the resonance was in the spectral range of 400–1700 nm and their sensitivity in aqueous salt solutions (NaCl), as well as chemical resistance in acids (HCl, HNO 3 , H 2 SO 4 , H 3 PO 4 ) were evaluated. The maximum sensitivity of the implemented sensors for media with refractive indices of 1.34–1.37 was 2950 nm/RIU, which is one of the highest values found in the literature for sensors with Al 2 O 3 coating. The dependence between the temperature of the synthesis of coatings and the rate of their dissolution in orthophosphoric acid is demonstrated. It is shown that an increase in sensitivity of up to 30 % can be realized by changing the roughness of the surface of the coating or silica glass.

Photoisomerization-induced LMR shift for UV radiation detection

Transparent ZnO–PVA binary composite for UV-A photo detector: optical, electrical and thermal properties followed by laser induced fluorescence

A Simple and Low-Cost Fiber-Optic Sensor Based on Photoluminescence for Temperature Independent Ultraviolet Detection

Polymer/ZnO hybrid materials for near-UV sensors with wavelength selective response

Single-molecule mid-IR detection through vibrationally-assisted luminescence

An IR Photodetector Using an Optically Cooled Micromirror as a Light Pressure Sensor

Incorporating Photochromic Viologen Derivative to Unprecedentedly Boost UV Sensitivity in Photoelectrochromic Hydrogel.

High-Performance Mid-IR to Deep-UV van der Waals Photodetectors Capable of Local Spectroscopy at Room Temperature

Enhancement of photocurrent and responsivity of Zn1-xMgxO (x=15%)-based ultraviolet detector by UV-ozone treatment

Enhanced UV light detection using wavelength-shifting properties of Silicon nanoparticles

Real-Time Quantitative Detection of Ultraviolet Radiation Dose Based on Photochromic Hydrogel and Photo-Resistance

Lossy mode resonance sensors based on lateral light incidence in nanocoated planar waveguides

Enhancing Photoelectric Response of Self-powered UV and Visible Detectors Using CuO/ZnO NRs Heterojunctions

Polymer:Fullerene Bimolecular Crystals for Near-Infrared Spectroscopic Photodetectors

Distributed Ultraviolet Sensor Based on Brillouin Optical Correlation-Domain Analysis Using An Azobenzene Polymer-Coated Optical Fiber

Spectral response tuning and realization of quasi-solar-blind detection in organic ultraviolet photodetectors

Photochromic Uranyl-Based Coordination Polymer for Quantitative and On-Site Detection of UV Radiation Dose

Increasing the sensitivity of chemically resistant lossy mode resonance-based sensors on Al 2 O 3 coatings

Interfacial State Induced Ultrasensitive Ultraviolet Light Photodetector with Resolved Flux Down to 85 Photons Per Second

Flexible ultraviolet photodetector based on single ZnO microwire/polyaniline heterojunctions

UV excitation thermal lens microscope for sensitive and nonlabeled detection of nonfluorescent molecules