Abstract:High undercooling rapid solidification process has a significant impact on the solidified microstructure and mechanical properties of materials. In this study, particles with a diameter range between 100 and 1100 μm of ternary Zr 50 Cu 40 Al 10 and Zr 49 Cu 46 Al 5 alloys were prepared by a drop tube. The evolution process of particle-solidified microstructure with decreasing particle diameter was analyzed using XRD, SEM, and TEM. For Zr 50 Cu 40 Al 10 alloy, the solidified microstructure in the particle diameter ranges of 200–1100 μm is composed of an amorphous phase and a primary B2-ZrCu high-temperature metastable phase. As the particle diameter reduces, the retained crystalline phase in the solidified microstructure decreases progressively, and the dendrite grain length gradually becomes finer. When the particle diameter is reduced to below 200 μm, the crystalline phase has completely disappeared, and the solidified microstructure evolves into a completely amorphous structure. For Zr 49 Cu 46 Al 5 alloy, in the particle diameter range of 400–1100 μm, the solidified microstructure consists of primary B19'-ZrCu phase, a small amount of Cu 10 Zr 7 phase and Zr 14 Cu 51 phase. As the particle diameter reduces, a grain refinement phenomenon also occurs in the solidified microstructure and the dendritic morphology changes from equiaxed grain to rod-shaped dendrite. The amorphous phase appears when the particle diameter is lowered to 470 μm and solidified microstructure evolves into a completely amorphous structure as the particle diameter is reduced to 146 μm. The nanoindentation results show that the micromechanical properties of amorphous composite microstructures are superior to the single component composition of crystalline or amorphous phase for Zr 50 Cu 40 Al 10 and Zr 49 Cu 46 Al 5 alloys. The reinforcement effect on the amorphous phase is related to the content of the second crystalline phase. Moreover, under similar particle diameters, the mechanical properties of Zr 50 Cu 40 Al 10 particles are always better than those of Zr 49 Cu 46 Al 5 particles.

A comparative study of the influence of milling media on the structural and microstructural changes in monoclinic ZrO2

Effects of Zr Addition on the Deformation Behavior, Microstructure and Mechanical Properties of Dental Ti Alloys

Raman spectroscopy of ball-milled TiO2

Effect of ball-milling on the phase structure and hydrogen storage properties of Ti0.9Zr0.1Mn1.5 alloy

Effect of CeO_2 and ZrO_2 Additives on Microstructure and Thermal Stability of High-Energy Ball Milling Al_2O_3 Powder

Structure and Thermal Stability of Nanostructured Iron-doped Zirconia Prepared by High-energy Ball Milling

Mechanical Alloying Process of the Zirconia–8 Mol % Yttria Ceramic Powder

Preparation of nano-sized 6MgO–2Y2O3–ZrO2 powders by a combined co-precipitation and high energy ball milling process

Dispersion and Structure Analysis of Nanocrystalline Ti- m ZrO₂ Composite Powder for Biomedical Applications

A quantitative microscopic view on the gas‐phase‐dependent phase transformation from tetragonal to monoclinic ZrO2

Influence of Sintering Temperatures on Material Properties and Corresponding Milling Machinability of Zirconia Ceramics

Effect of ball-milling parameter on mechanical and damping properties of sintered Mg-Zr alloy

Internal Stress and Grain Size Effect on the Phase Stabilization of ZrO2 Deposited by MOCVD

Crystalline and amorphous microstructure evolution of Zr-Cu-Al ternary alloys solidified in drop tube

Deformation-induced Reactions of ZnO and TiO2

Microstructure and High Temperature Deformation Behavior of the Mo-ZrO 2 Alloys

Phase composition and microstructure of new Ti–Ta–Nb–Zr biomedical alloys prepared by mechanical alloying method

Characterization of Zirconia-Based Ceramics After Microgrinding

Grain size distribution analysis of MgO and VC inhibited zirconia toughened alumina ceramics using digital image processing

Microstructural Evolution During High Energy Ball Milling of Fe2o3-Sio2 Powders

Correlation Between Microstrain and Crystallite Size in Alumina