Abstract:Under nonsink dissolution conditions, the kinetic-solubility profiles of amorphous solid dispersions (ASDs) based on soluble carriers typically exhibit so-called "spring-and-parachute" concentration-time behaviors. However, the kinetic-solubility profiles of ASDs based on insoluble carriers (including hydrogels) are known to show sustained supersaturation during nonsink dissolution through a matrix-regulated diffusion mechanism by which the supersaturation of the drug is built up gradually and sustained over an extended period without any dissolved polymers acting as crystallization inhibitors. Despite previous findings demonstrating the interplay between supersaturation rates and total doses on the kinetic-solubility profiles of soluble amorphous systems (including ASDs based on dissolution-regulated releases from soluble polymer carriers), the combined effects of supersaturation rates and doses on the kinetic-solubility profiles of ASDs based on diffusion-regulated releases from water-insoluble carriers have not been investigated previously. Thus, the objective of this study is to examine the impacts of total doses and supersaturation-generation rates on the resulting kinetic-solubility profiles of ASDs based on insoluble hydrogel carriers. We employed a previously established ASD-carrier system based on water-insoluble-cross-linked-poly(2-hydroxyethyl methacrylate) (PHEMA)-hydrogel beads and two poorly water soluble model drugs: the weakly acidic indomethacin (IND) and the weakly basic posaconazole (PCZ). Our results show clearly for the first time that by using the smallest-particle-size fraction and a high dose (i.e., above the critical dose), it is indeed possible to significantly shorten the duration of sustained supersaturation in the kinetic-solubility profile of an ASD based on a water-insoluble hydrogel carrier, such that it resembles the spring-and-parachute dissolution profiles normally associated with ASDs based on soluble carriers. This generates sufficiently rapid initial supersaturation buildup above the critical supersaturation, resulting in more rapid precipitation. Above this smallest-particle-size range, the matrix-diffusion-regulated nonlinear rate of drug release gets slower, which results in a more modest rate of supersaturation buildup, leading to a maximum supersaturation below the critical-supersaturation level without appreciable precipitation. The area-under-the-curve (AUC) values of the in vitro kinetic-solubility concentration-time profiles were used to correlate the corresponding trends in dissolution enhancement. There are observed monotonic increases in AUC values with increasing particle sizes for high-dose ASDs based on water-insoluble hydrogel matrixes, as opposed to the previously reported AUC maxima at some intermediate supersaturation rates or doses in soluble amorphous systems, whereas in the case of low-dose ASDs (i.e., below the critical dose levels), crystallization would be negligible, leading to sustained supersaturation with all particle sizes (i.e., eventually reaching the same maximum supersaturation) and the smallest particle size reaching the maximum supersaturation the fastest. As a result, the smallest particle sizes yield the largest AUC values in the case of low-dose ASDs based on water-insoluble hydrogel matrixes. In addition to probing the interplay between the supersaturation-generation rates and total doses in ASDs based on insoluble hydrogel carriers, our results further support the fact that through either increasing the hydrogel-particle size or lowering the total dose to achieve maximum supersaturation still below the critical-supersaturation level, it is possible to avoid drug precipitation so as to maintain sustained supersaturation.

Effect of basket mesh size on the hydrodynamics of a partially filled (500 mL) USP rotating basket dissolution testing apparatus 1

Experimental Investigation on Solid Particle Distribution in Dense Solid–liquid Stirred Tank

Effects of Glass Bead Size on Dissolution Profiles in Flow-through Dissolution Systems (USP 4)

Intrinsic dissolution rate modeling for the pharmacopoeia apparatus rotating disk compared to flow channel method

Influence of higher rates of agitation on release patterns of immediate-release drug products

In vitro and in silico methods to investigate the effect of moderately increasing medium viscosity and density on ibuprofen dissolution rate

Probing Differences in Mass-Transfer Coefficients in Beaker and Stirrer Digestion Systems and the USP Dissolution Apparatus 2 Using Benzoic Acid Tablets

Preliminary investigations of the suitability of the USP uniformity of dosage units tests for evaluating the uniformity of powder blends and their corresponding tablets

Can the USP paddle method be used to represent in-vivo hydrodynamics?

Mixing of Monoclonal Antibody Formulated Drug Substance Solutions in Square Disposable Vessels

Feasibility studies in spheronization and scale-up of ibuprofen microparticulates using the rotor disk fluid-bed technology

Suppository Dissolution Testing: Apparatus Design and Release of Aspirin

Impact of grinding balls on the size reduction of Aprepitant in wet ball milling procedure

Optimizing Nonsink Dissolution Testing for Amorphous Solid Dispersions: Exploring Sample Handling Variables

Combined Effects of Supersaturation Rates and Doses on the Kinetic-Solubility Profiles of Amorphous Solid Dispersions Based on Water-Insoluble Poly(2-hydroxyethyl methacrylate) Hydrogels.

Impact of Surface Tension, Viscosity, Pump Settings, and Nozzle Size on Filling Process Capability and Accuracy in High-Concentration Biopharmaceuticals

Varied Bulk Powder Properties of Micro-Sized API within Size Specifications as a Result of Particle Engineering Methods

Effect of Differential Surface Anisotropy on Dissolution Behavior of Fenofibrate Crystal Habits: Comparative Study using USP Type 2 and Type 4 Dissolution Apparatuses

Biphasic Dissolution as an Exploratory Method during Early Drug Product Development

Transport properties and size exclusion effects in wide-pore superficially porous particles

Studying the API Distribution of Controlled Release Formulations Produced via Continuous Twin-Screw Wet Granulation: Influence of Matrix Former, Filler and Process Parameters