Abstract:Injection of CO2 and water in saline aquifers or oil reservoirs causes changes of pressure, saturation and concentrations that affect the state of stress and promote chemical reactions in the host rock, resulting in porosity and permeability variations. It is therefore a coupled hydro-mechanical and chemical (HMC) problem. Numerical simulation of multiphase and multicomponent flow of CO2, oil and water with mechanical coupling allows realistic modeling of the reservoir and cap rocks. Carbonate reservoirs are geological formations composed mainly of minerals such as calcite and dolomite which can dissolve or precipitate in the medium when injecting a fluid of chemical composition and temperature different from those of the fluids initially contained in the rock. Water-weakening due to matrix acidification of carbonates is a well-known phenomenon that can be modeled by including mineral concentrations as state variables in the stress-strain behavior of the material. The objective of this work is to characterize synthetic carbonate rocks through microtomography and petrography techniques, focusing on a comparative analysis before and after load application and degradation with a reactive fluid [1]. The synthetic rocks were subjected to physical characterization (mineralogy, computed tomography and porosity) and mechanical characterization (uniaxial compressive strength and Brazilian tests) before and after the dissolution process. The petrographic analysis verified an increase in both intergranular and intragranular porosities after dissolution. The microtomography analysis quantified the maximum increase in porosity, from 11.8% to 41.3% in the two-dimensional analysis and 31.6% to 52% in the three-dimensional analysis of the porous structures. Furthermore, the pores were quantified according to their area, and data was obtained on the orientation of the pores, providing insight into the preferred paths of fluid flow. It was also observed that the microtomography technique was an effective tool for characterizing fractures in the samples before and after dissolution [1]. Dissolution tests were also performed in a modified oedometer cell adapted to measure horizontal stress. The dissolution phase was conducted using water and an acid solution to evaluate the influence of the pH on the mechanical behaviour of the samples. When the sample in the oedometric cell is exposed to an acid solution under constant vertical load of 400kPa, vertical displacement takes place (volume decrease of the sample) and horizontal stress increases (Figure 1). The synthetic rock used in this experiment is mainly composed by calcite, with small additions of calcium hydroxide, and the reactive fluid is water acidified with acetic acid (with 10% concentration). This material is manufactured in laboratory in order to have greater control of its constituents and reproducibility of experimental results. During the acidification phase of the experiment, the sample was subjected to an acid flow with a pressure differential of 12kPa for 7h. The behavior in Figure 1 was also observed by [2] and [3]. The model for degradation of carbonatic soft rocks proposed by [2] was implemented in a finite element code capable of performing coupled THMC analyzes in porous media [4]. This model is based on the Critical State Theory with the introduction of a bonding variable that controls the size of the yield surface by modifying the tensile strength and the pre-consolidation stress of the material. In Figure 1 it is also possible to see that the HMC coupled simulation of the oedometric test was able to reproduce the experimental results in terms of volumetric strain and horizontal stress. In Figure 2 tomographic images of the synthetic carbonate rock before and after exposure to the acid solution in an oedometric cell under constant vertical load are presented. Such analyses are crucial for the injection of reactive fluids, such as CO2, at high depths. Dissolution of minerals will affect not only the porosity and permeability of the reservoir rock but also, possibly, the stress state in the vicinity of the injection well.

The Influence of Desalinization of Reservoir Rocks on Their Mechanical and Filtration Properties by Example of the Chayanda Field

Changes in filtration and capacitance properties of highly porous reservoir in underground gas storage: CT-based and geomechanical modeling

An Experimental Study of CO2–brine–rock Interaction at in Situ Pressure–temperature Reservoir Conditions

Impact of Oilfield Chemicals on Contiguous Technologies

Theoretical and experimental investigation of the impact of oil functional groups on the performance of smart water in clay-rich sandstones

Numerical modeling and experimental investigation on the effect of low-salinity water flooding for enhanced oil recovery in carbonate reservoirs

The Analysis of Injected Water into O-1 Formation of the Central Block of the Talakan Oil and Gas Condensate Field in Order to Identify and Predict Zones With High Risk of Salt Precipitation

Investigation of modified Water chemistry for improved oil recovery: Application of DLVO theory and surface complexation model

Study on the rock physical mechanical properties evaluation of tight oil reservoir in Chang 7 member, Longdong area, Ordos Basin, China

Experimental evaluation of tight sandstones reservoir flow characteristics under CO2–Brine–Rock multiphase interactions: A case study in the Chang 6 layer, Ordos Basin, China

Impacts of inorganic salts ions on the polar components desorption efficiency from tight sandstone: A molecular dynamics simulation and QCM-D study

Experimental investigation of geochemical and mineralogical effects of CO2 sequestration on flow characteristics of reservoir rock in deep saline aquifers

Laboratory study on the factors affecting hydraulic fracturing effect for inter-salt oil shale layers, Qianjiang Depression, China

Fundamental Aspects of Oilfield Development with Water Breakthrough Risks - Time for a Paradigm Change

Minerals Dissolution Effect on the Mechanical Properties of Synthetic Carbonate Rocks

The Indicative Role of Geochemical Characteristics of Fracturing Flowback Fluid in Shale Gas Wells on Production Performance

Effect of the Type and Concentration of Salt on Production Efficiency in Smart Water Injection into Carbonate Oil Reservoir Rocks

Assessing salt precipitation and weak acid interaction in subsurface CO2 injection: Potential 50% strength decline in near-wellbore reservoir sandstones

Micro-mechanics Based Numerical Simulation of NaCl Brine Induced Mechanical Strength Deterioration of Sedimentary Host-Rock Formations

Influence of Sodium Ferrocyanide as an Alternative Inhibitor of Sodium Chloride Crystallization in Tight Sandstone Gas Wells

Microscopic enrichment and porosity-permeability reduction mechanism of residual oil in tight sandstone reservoirs: an insight from Chang 8 Member, Yanchang Formation, Ordos Basin, China