Abstract:Summary Creating sufficient and sustained fracture conductivity contributes directly to the success of acid-fracturing treatments. The permeability and mineralogy distributions of formation rocks play significant roles in creating nonuniformly etched surfaces that can withstand high closure stress. Previous studies showed that, depending on the properties of formation rock and acidizing conditions (acid selection, formation temperature, injection rate, and contact time), a wide range of etching patterns (roughness, uniform, channeling) could be created that can dictate the resultant fracture conductivity. Insoluble minerals and their distribution can completely change the outcomes of acid-fracturing treatments. However, most experimental studies use homogeneous rock samples such as Indiana limestone that do not represent the highly heterogeneous features of carbonate rocks. This work studies the effect of heterogeneity and, more importantly, the distribution of insoluble rock on acid-fracture conductivity. In this research, we conducted acid-fracturing experiments using both homogeneous Indiana limestone samples and heterogeneous carbonate rock samples. The Indiana limestone tests served as a baseline. The highly heterogeneous carbonate rock samples contain several types of insoluble minerals such as quartz and various types of clays along sealed natural fractures. These minerals are distributed in the form of streaks correlated against the flow direction, or as smaller nodules. After acidizing the rock samples, these minerals acted as pillars that significantly reduced conductivity-decline rate at high closure stresses. Both X-ray diffraction (XRD) and X-ray fluorescence (XRF) tests were performed to pinpoint the type and location of different minerals on the fracture surfaces. A surface profilometer was also used to correlate conductivity as a function of mineralogy distribution by comparing the surface scans from after the acidizing test to the scans after the conductivity test. Theoretical models considering geostatistical correlation parameters were used to match and understand the experimental results. Results of our study showed that insoluble minerals with higher-strength mechanical properties were not crushed at high-closure stress, resulting in a less-steep conductivity decline with an increasing closure stress. If the acid etching creates enough conductivity, the rock sample can sustain a higher closure stress with a much lower decline rate compared with Indiana limestone samples. Fracture surfaces with insoluble mineral streaks correlated against the flow direction offer the benefit of being able to maintain conductivity at high closure stress, but not necessarily high initial conductivity. Using a fracture-conductivity model with correlation length, we matched the fracture-conductivity behavior for the heterogeneous samples. Fracture surfaces with mineral streaks correlated with the flow direction could increase acid-fracturing conductivity significantly as compared to the case when the streak is correlated against the flow direction. The results of the study show that fracture conductivity can be optimized by taking advantage of the distribution of insoluble minerals along the fracture surface and demonstrate important considerations to make the acid-fracturing treatment successful.

Influence of grade heterogeneity and gangue mineralogy on the efficacy of high voltage pulse enabled ore pre-concentration

Pre-weakening behavior of magnetite quartzite based on high-voltage pulse discharge

A novel technology of high-voltage pulse discharge for comminution of galena ore

Numerical modeling and simulation of the electric breakdown of rocks immersed in water using high voltage pulses

Identifying Separation Potency and Relationship of Grade and Density of Copper Ore for Gravity-Based Early Coarse Gangue Rejection using Statistical Method

Separation and Preparation of Level I Standard Lead Concentrate from Lead Ore Via S-HGMS Technology: Description of Separation Mechanism

Enhancement of magnetization roasting of hematite ore by high voltage pulse discharge

Insights Into Ferric Leaching Of Low Grade Metal Sulfide-Containing Ores In An Unsaturated Ore Bed Using X-Ray Computed Tomography

Can preconcentration of cassiterite from its pegmatite ore reduce processing costs and improve operational sustainability?

Investigating the benefits of using HPGR prior to cyanidation of low grade gold ore

Experimental Study on Efficient Recovery of High-Grade Sulfide Ore

Evaluation of Ni-Cu Ore from Zapolyarnoe Based on Mineralogical and Physical Properties before and after Comminution

The Development of Preconcentration Technology in Low-Grade Magnetite’s Beneficiation

Effects of Heterogeneity in Mineralogy Distribution on Acid-Fracturing Efficiency

Recent Advances in Studying Colloidal Interactions in Mineral Processing

Characterization of chalcopyrite ore under high voltage pulse discharge: Particle size distribution, fractal dimension, specific energy consumption, grinding kinetics

The deleterious role of gangue mineralogy in copper extraction: A case study of poor recovery in leaching low-grade Cu ores

Strengthening Liberation and Separation of Magnetite Ore Via Magnetic Pulse Pretreatment: an Industrial Test Study

Factors controlling the formation of large porphyry Cu deposits: A case study from the Jiurui ore district of Middle-Lower Yangtze River Metallogenic Belt using in situ zircon and apatite chemistry from syn-mineralization intrusions

A methodology for gangue management in the flotation of a PGM-bearing ore through laboratory tests, mineralogical analysis and circuit modelling

Experimental Research on Beneficiation Process a Low-grade Cu-Pb-Zn Polymetallic Sulfide Ore from Xinjiang