Abstract:The clinical significance of increased wear can mainly be attributed to impaired aesthetic appearance and/or functional restrictions. Little is known about the systemic effects of swallowed or inhaled worn particles that derive from restorations. As wear measurements in vivo are complicated and time-consuming, wear simulation devices and methods had been developed without, however, systematically looking at the factors that influence important wear parameters. Wear simulation devices shall simulate processes that occur in the oral cavity during mastication, namely force, force profile, contact time, sliding movement, clearance of worn material, etc. Different devices that use different force actuator principles are available. Those with the highest citation frequency in the literature are - in descending order - the Alabama, ACTA, OHSU, Zurich and MTS wear simulators. When following the FDA guidelines on good laboratory practice (GLP) only the expensive MTS wear simulator is a qualified machine to test wear in vitro; the force exerted by the hydraulic actuator is controlled and regulated during all movements of the stylus. All the other simulators lack control and regulation of force development during dynamic loading of the flat specimens. This may be an explanation for the high coefficient of variation of the results in some wear simulators (28-40%) and the poor reproducibility of wear results if dental databases are searched for wear results of specific dental materials (difference of 22-72% for the same material). As most of the machines are not qualifiable, wear methods applying the machine may have a sound concept but cannot be validated. Only with the MTS method have wear parameters and influencing factors been documented and verified. A good compromise with regard to costs, practicability and robustness is the Willytec chewing simulator, which uses weights as force actuator and step motors for vertical and lateral movements. The Ivoclar wear method run on the Willytec machine shows a mean coefficient of variation in vertical wear of 12%. Force measurements have revealed that in the beginning of the stylus/specimen contact phase the force impulse is 3-4 times higher during dynamic loading than during static loading. When correlating material properties to the wear results of 23 composite resins subjected to the Ivoclar method, some parameters could be identified and incorporated into a wear formula to predict wear with the Ivoclar method. A round robin test evaluating the wear of ten dental materials with five wear simulation methods showed that the results were not comparable, as all methods follow different wear testing concepts. All wear methods lack the evidence of their clinical relevance because prospective studies correlating in vitro with long-term in vivo results with identical materials are not available. For direct restorative materials, amalgam seems to be a realistic reference material. For indirect, namely crown and bridge materials, low strength ceramic is appropriate.

Evaluation of the effectiveness of the new tooth wear measurement parameters

Clinical and digital assessment of tooth wear

[Preliminary Study of Tooth Measured by a Noncontact 3D Image Survey System].

Design of Occlusal Wear Facets of Fixed Dental Prostheses Driven by Personalized Mandibular Movement.

An accurate and efficient method for occlusal tooth wear assessment using 3D digital dental models

The effect of dental restoration geometry and material properties on biomechanical behaviour of a treated molar tooth: A 3D finite element analysis

3D Method for Occlusal Tooth Wear Assessment in Presence of Substantial Changes on Other Tooth Surfaces

Three-dimensional Analysis for Parameters Relating to Balanced Occlusion of Complete Denture

The Effect of Residual Dentition on the Dynamic Adjustment of Wear Facet Morphology on a Mandibular First Molar Crown

Automated monitoring of tooth wear progression using AI on intraoral scans

Evaluation of the assessment of tooth wear by general dental practitioners

Evaluation of Accuracy of Virtual Occlusal Definition in Angle Class I Molar Relationship

Influence of Scanner Precision and Analysis Software in Quantifying Three-Dimensional Intraoral Changes: Two-Factor Factorial Experimental Design

Construction of a Novel Digital Method for Quantitative Analysis of Occlusal Contact and Force

The three-dimensional measurements and analysis of anatomic artificial teeth cusp inclination

Accuracy of Two Best-Fit Alignment Strategies with Different Reference Areas for Wear Measurement with an Intraoral Scanner: an in Vitro Study.

Methods of measuring wear of teeth

How to qualify and validate wear simulation devices and methods

Occlusal and Labial/Buccal Approaches for Measuring MesioDistal Width of Teeth on Chairside Digitally Scanned Models

Evaluation of wear resistance of dental resin composites with a 3D profilometer

In vivo evaluation of the reliability and validity of three digital occlusion analysis methods