Abstract:Due to the advantages of low cost, easy fabrication, mechanical flexibility, the research on organic solar cells has attracted a lot of attentions in the last decades. Among countless organic materials, the most successful ones are conjugated polymers, which were widely used in bulk heterojunction (BHJ) in conjugation with the fullerene [1]. In view of the fact the interpenetratedphase-separated p-n composites offer more chances for excitons to reach the p-n interfaces, BHJ greatly facilitates the dissociation of photogenerated excitons before decaying to ground state. During exciton dissociation process, the exciton delocalization at an ultra fast timescale has been observed recently, which has considerable effects on the charge generation and device performance. In this work, based on the recent studies [2–4], we established a theoretical model of polymer solar cells (PSCs) incorporating the exciton delocalization process. Through the model, we found the increase of delocalized excitons (compared to the total generated excitons) will significantly improve the short-circuit current, open-circuit voltage, fill factor and power conversion efficiency of PSCs. Particularly, the saturations of fill factor and open-circuit voltage are also observed, and the saturation points depend on the active layer thickness and recombination rate. For instance,the device model of 200nm thickness active layer has the saturated fill factor at 70% delocalization ratio, which is close to the conventional ratio of practical devices. The device configuration studied comprises a BHJ active layer sandwiched between a transparent anode and a metal cathode. Moreover, the active material is a mixture of OC 1 C 10 -PPV, as the donor, and PCBM, as the acceptor [5]. The generation rate of excitons is assumed to be homogeneous. The model proposed involves both the drift-diffusion model for photocarriers (Eq. (1)) and the diffusion and dissociation model for excitons (Eq. (2)). The governing equations are given as follows equation where q is elementary charge, n(p) is the electron (hole) density, and r G , r R are the parametersfor controlling exciton generation and bulk recombination, respectively. E is the internal E-field. µ and D are the mobility and diffusion coefficients. The exciton density is denoted by X diff and k diss is the exciton dissociation rate. The recombination R is taken to be a bimolecular form,with the rate given by Langevin [6], and η s is 0.25 for the singlet excitons. Using the physical parameters given by experiments [5], the nonlinear governing equation sets are solved self-consistently. The excitons are delocalized at an ultra fast timescale to form electron-hole pairs, which is much faster than the photo carrier relaxation time and exciton diffusion time. Consequently, the delocalization process was simulated by directly inserting the delocalization ratio η del into the equations.

Excited‐State Dynamics in All‐Polymer Blends with Polymerized Small‐Molecule Acceptors

The Role Of Exciton Delocalization In The Performance Of Bulk-Heterojunction Polymer Solar Cells

Mesomeric control of the optoelectronic properties of polymerized small molecule acceptors

Polymerizing M‐Series Acceptors for Efficient Polymer Solar Cells: Effect of the Molecular Shape

Synchronously regulating the alkyl side-chain and regioisomer of polymerized small molecule acceptor enabling highly efficient all-polymer solar cells processed with non-halogenated solvent

Photoinduced Polaron Formation in a Polymerized Electron-Acceptor Semiconductor

Manipulating Polymer Backbone Configuration via Halogenated Asymmetric End-Groups Enables Over 18% Efficiency All-Polymer Solar Cells

Regioregular polymerized small-molecule acceptors for high-performance all-polymer solar cells

Polymerized Small‐Molecule Acceptor as an Interface Modulator to Increase the Performance of All‐Small‐Molecule Solar Cells

Mesomeric control of the optoelectronic properties of polymerized small molecule acceptors

An Improved Performance of All Polymer Solar Cells enabled by Sequential Processing via Non-halogenated Solvents

Recent research progress of all-polymer solar cells based on PSMA-type polymer acceptors

A polymer acceptor with grafted small molecule acceptor units for high efficiency organic solar cells

Recent progress and prospects of dimer and multimer acceptors for efficient and stable polymer solar cells

Effect of Isomerization of Linking Units on the Photovoltaic Performance of PSMA-Type Polymer Acceptors in All-Polymer Solar Cells

Tethered Small-Molecule Acceptors Simultaneously Enhance the Efficiency and Stability of Polymer Solar Cells.

New Type of Polymerized Small A-D-A Acceptors Constructed by Conjugation Extension in the Branched Direction

Tethered Small‐Molecule Acceptors Simultaneously Enhances the Efficiency and Stability of Polymer Solar Cells

Efficient all-polymer solar cells based on a narrow-bandgap polymer acceptor

The Role of Device Mobility on the Charge Generation Process in Polymerized Small-Molecule Acceptor Based Organic Solar Cells

An Asymmetric Polymerized Small Molecular Acceptor with Temperature-Dependent Aggregation and Superior Batch-to-batch Reproducibility for Efficient All-Polymer Solar Cells