Abstract:The development of a method to calculate the efficiency and the methodology to enhance the efficiency is not the ultimate goal. Mainly, the calculated results obtained by using a mathematical relationship and a physical law should be applied in day to day life applications for the benefit of society. In this work, we have developed the theoretical prototype and improved the technique for installing the thermoelectric generator (TEG) setup in automobiles. We have applied the methodology for enhancement in the efficiency of TEG and made it economical and user friendly. We have considered a linear curve fit from a zigzag curve of the reported mass flow rate and temperature variation at the hot gas inlet. Accordingly, the temperature of the coolant is also varied linearly at the inlet from 300 K to 320 K, corresponding to the mass flow rate of the coolant. Circular fins are installed around each circular layer of thermoelectric materials (TEMs) after the water jacket. The heat loss through each fin is calculated to be 24 W. The energy balance is done at each and every TEM, and correspondingly, we have calculated the amount of power transferred through each segment of TEG as 32 W. We have calculated the length of the TEM sample for attaining the respective temperature range for the hybrid of Bi2Te3 and TiO1.1. This calculation is done by considering the compatibility factor derived as s=1+ZT−1αT, which is a function of only intrinsic material properties and temperature, which is represented by a ratio of current density to conduction heat flux. The length obtained for this particular combination is ∼8 mm. To this end, we have reported the efficiency with respect to the mass flow rate of hot flue gas from automobiles for different layers of TEG for the above mentioned combination. Here, we have explored the possibility of installing a number of different layers of the TEG module which can be installed throughout the lateral surface area of the exhaust chamber. Thermal mismatching criteria are also discussed at the adjoining surface of TEMs because of high temperature. To maintain the thermal expansion or contraction of TEMs, spring and bolt arrangement is provided, which is fixed over the aluminium oxide ceramic substrate. Ideal power output by the first layer is also calculated using a temperature dependent material parameter, which is 100 W and plotted in a graph showing the change in power output with a variation in the temperature of sink. For automobiles, if the temperature of the source is considered as 800 K, so for the temperature range of 300 K to 800 K, the power obtained is 58 W.

Development of thermoelectric exhaust energy recovery system of a hydrogen internal combustion engine in a city bus using a Three-Dimensional multiphysics model

Thermoelectric Generation from Exhaust Heat in Electrified Natural Gas Trucks: Modeling and Analysis of an Integrated Engine System Performance Improvement

Simulation, Experimentation, and Collaborative Analysis of Adjacent Heat Exchange Modules in a Vehicular Cooling System

Experiments on Waste Heat Thermoelectric Generation for Passenger Vehicles

Simulation Research On The Application Of Thermoelectric Waste Heat Recovery Of Internal Combustion Engine

Performance Investigation of a Thermoelectric Generator System Applied in Automobile Exhaust Waste Heat Recovery

Modelling and Simulation Study of a Converging Thermoelectric Generator for Engine Waste Heat Recovery

Theoretical Analysis of Energy Recovery Potential for Different Types of Conventional Vehicles with a Thermoelectric Generator

Thermoelectric cooler performance enhancement using thermoelectric generators and their use as a single model to improve the performance of thermal battery management systems for electric vehicles

Comparison and Parametric Analysis of Thermoelectric Generator System for Industrial Waste Heat Recovery with Three Types of Heat Sinks: Numerical Study

Dynamic performance of a polygonal thermoelectric generator using sickle-shaped fins for automotive application

Experimental investigation of waste heat recovery potential from car radiator with thermoelectric generator

Calculation of efficiency and power output by considering different realistic prospects for recovering heat from automobile using thermoelectric generator

Innovative Design of an Annular Thermoelectric Generator for Enhanced Automotive Waste Heat Recovery

Performance analysis of a novel Two-stage automobile thermoelectric generator with the Temperature-dependent materials

Experimental Study of Thermoelectric Generation from Automobile Exhaust

Performance study on a thermoelectric generator with exhaust-module-coolant direct contact

Development of two transient models for predicting dynamic response characteristics of an automobile thermoelectric generator system

Dynamic behaviour of automobile thermoelectric waste heat recovery under different driving cycles

Numerical study of a novel automotive thermoelectric generator system equipped with segmented converging heat exchanger

A comprehensive hybrid transient CFD-thermal resistance model for automobile thermoelectric generators