Abstract:Solid oxide electrolysis cells (SOEC) have been receiving significant attention recently because of their high energy efficiency and fast hydrogen production. In our previous study, a multi-physics modeling framework to simulate the SOEC performance and structural reliability of planar SOEC design was developed and demonstrated. The electrochemical reactions, fluid dynamics, species transport, electron transfer, and heat transfer were modeled in the commercial computational fluid dynamics (CFD) software STAR-CCM+. The thermomechanical analysis and the associated structural reliability evaluations were conducted using the commercial finite element analysis software ANSYS. The electrochemistry model was validated by using the experimentally obtained current-voltage (I-V) characteristics of the electrode-supported SOECs. In this study, this framework was applied on a large 300 cm 2 steam planar SOEC design, and systematically studied the structural reliability under combinations of cell operating conditions, with cell voltage 1-1.5 V, steam fraction in fuel inlet 0.7-0.9, air inlet flow rate 0-10 L/min, fuel inlet flow rate 2.5-12.5 L/min, and inlet temperature 600-900 C. In the modeling framework, all the cells were investigated under the adiabatic thermal conditions, which is equivalent to packing the cell in an insulated container. This induced the relatively larger temperature variation than in the smaller cell designs. This cell internal temperature non-uniformity may further enhance the spatial variations of open circuit voltage, activation loss, and ionic conductivity in the cell, which all influence the overall cell performance. This situation is more obvious when the cell voltage is higher than 1.35V, under which the cell is significantly heated along the steam flow direction. Traditionally, it is assumed that the cell internal temperature spatial variation plays an important role on cell structural reliability. However, because it was assumed that all the components in cell are stress free at 850 , the cell temperature deviation from 850 is more critical to the stress distribution and structural reliability in the cell. For the investigated cells in the practical conditions, like 750 C inlet temperature and varying voltage from 1.05 to 1.5 V, the highest first principal stress is always in the air side electrode, which is around 45 MPa. This is explained by the higher coefficient of thermal expansion of LSCF-GDC with respect to the other layers. This may indicate that the failure would possibly occur in the air side electrode, but at low risk due to the relatively higher Weibull characteristic strength.

Numerical Study of H2 Production and Thermal Stress for Solid Oxide Electrolysis Cells with Various Ribs/Channels

Solid Oxide Electrolysis Cell under Real Fluctuating Power Supply with a Focus on Thermal Stress Analysis

Numerical study on thermal stress of solid oxide electrolyzer cell with various flow configurations

Towards Feasible Temperature Management and Thermo-Mechanical Stability of Carbon-Assisted Solid Oxide Electrolysis Cell

Numerical simulation and analysis of the thermal stresses of a planar solid oxide electrolysis cell

Numerical Modeling and Current Collection Designs for Flat-Chip Solid Oxide Fuel Cell

Optimization Design of Rib Width and Performance Analysis of Solid Oxide Electrolysis Cell

Component-level modeling of solid oxide water electrolysis cell for clean hydrogen production

Comprehensive Modeling of Tubular Solid Oxide Electrolysis Cell for Co-Electrolysis of Steam and Carbon Dioxide

Numerical Investigation of Heat/Flow Transfer and Thermal Stress in an Anode-Supported Planar SOFC

Integrated modeling of electrochemical, thermal, and structural behavior in solid oxide electrolysis cells

Coupled Electrochemical-Thermo-Stress Analysis for Methanol-Fueled Solid Oxide Fuel Cells

Numerical Analysis of Thermal Stress for a Stack of Planar Solid Oxide Fuel Cells

Numerical Investigation on the Performance of IT-SOEC with Double-Layer Composite Electrode

Analysis of performance optimization of high‐temperature solid oxide electrolytic cell based on the coupling of flow, heat, and mass transfer and electrochemistry

Numerical simulation of flow channel geometries optimization for the planar solid oxide electrolysis cell

2D thermal modeling of a solid oxide electrolyzer cell (SOEC) for syngas production by H2O/CO2 co-electrolysis

Modeling and analysis of cross-flow solid oxide electrolysis cell with oxygen electrode/electrolyte interface oxygen pressure characteristics for hydrogen production

Structural Reliability Analysis of Large Planar Steam Solid Oxide Electrolysis Cells

Performance and Thermal Stress Evaluation of Full-Scale SOEC Stack Using Multi-Physics Modeling Method

Numerical Simulation of Tubular Solid Oxide Fuel Cells