Abstract:Integrating phase change materials (PCMs) with concentrated photovoltaic-thermoelectric (PV-TE) systems can effectively control the interface temperature between PV and TE components and improve the full solar-spectrum utilization efficiency. However, since the structure of photovoltaic-phase change material-thermoelectric (PV-PCM-TE) systems is complex and the temperatures among the components are coupled and affect each other, the photo-thermal-electric conversion characteristics under the actual physical properties need to be analyzed by a more detailed model, and the suitable operating conditions for PV-PCM-TE systems remain clear. There is still a lack of the method for improving the system performance. Therefore, a three-dimensional transient model is established herein by combining the Monte Carlo ray-tracing method and finite volume method to simulate the complex energy conversion processes of the PV-PCM-TE system. Based on this, performances of PV-PCM-TE, PV-TE, and PV systems are compared under different operating conditions, and the applicable conditions for PV-PCM-TE systems are analyzed. Then effects of key parameters of the phase change module are investigated. In the end, to further improve the system performance, a partition screening method of PCM is proposed considering the nonuniform solar radiation on photovoltaic surfaces, and the selection and layout area of PCMs are optimized. The results present that the applicable operating conditions are low concentration ratio (< 20) and low heat transfer coefficient (< 20 W·m-2·K-1). In terms of structural parameters, the system power generation is most significantly affected by the width. In terms of PCM physical properties, it is most affected by the PCM density, followed by latent heat. For different concentration ratios, there are different optimal melting points to achieve the highest power generation. The proposed PCM partition screening method can efficaciously control PV-TE interface temperature, and reduce photovoltaic cells' temperature by 47°C. The system efficiency can be increased by 4.8% and 4.2% after the optimization compared with that of the single PV cell and the traditional PV-TE system, respectively.

Aerodynamic heat utilization based on thermophotovoltaic-composite phase change material-thermoelectric hybrid system

Parametric Characteristics and Optimization of a Novel Near-Field Thermophotovoltaic and Thermoelectric Hybrid System for Energy Harvest

Integration of thermal insulation and thermoelectric conversion embedded with phase change materials

Performance Analysis and Structure Optimization for Concentrated Photovoltaic-Phase Change Material-Thermoelectric System in Space Conditions

Operational and structural parametric analysis of a photovoltaic/thermal system integrated with phase change material

Numerical Analysis of a TEG and mPCM Enhancement System for BIPVs Using CFD

Experimental Investigation on Potential of a Concentrated Photovoltaic-Thermoelectric System with Phase Change Materials

MODEL DEVELOPMENT AND PERFORMANCE IMPROVEMENT OF A PHOTOVOLTAIC-THERMOELECTRIC SYSTEM BY INTEGRATING AND OPTIMIZING PHASE CHANGE MATERIALS

Thermoelectric Energy Harvesting Using Phase Change Materials (PCMs) in High Temperature Environments in Aircraft

Experimental thermal and electrical performance analysis of a concentrating photovoltaic/thermal system integrated with phase change material (PV/T-CPCM)

Performance analysis of a hybrid photovoltaic-thermoelectric generator system using heat pipe as heat sink for synergistic production of electricity

Conversion Efficiency Gain for Concentrated Triple-Junction Solar Cell System Through Thermal Management

Enhanced Thermal Performance of a Thermoelectric Generator with Phase Change Materials

Experimental investigation of novel integrated photovoltaic-thermoelectric hybrid devices with enhanced performance

Periodic Energy Transmission and Regulation of Photovoltaic-Phase Change Material-Thermoelectric Coupled System under Space Conditions

Experimental Investigation on Effects of Thermal Resistances on a Photovoltaic-Thermoelectric System Integrated with Phase Change Materials

Optimized output electricity of thermoelectric generators by matching phase change material and thermoelectric material for intermittent heat sources

Research and numerical analysis on performance optimization of photovoltaic-thermoelectric system incorporated with phase change materials

Structural optimization of thermoelectric modules in a concentration photovoltaic-thermoelectric hybrid system

Numerical analysis of a solar driven thermoelectric generator brick with phase change materials: Performance evaluation and parametric investigations

Experimental study on an integrated system of thermosyphon loop and vapor compression assisted with phase change material for pulse heat load