Abstract:The control of temperature in lithium-ion stacks is of increasing industrial importance. In fact, an efficient thermal conditioning system ensures a homogeneous temperature distribution among the cells, preventing conditions which could hinder performance or led to temperature runaway and so a disruptive failure of the module. CFD models for thermal analysis can be useful in the design phase to optimize the module layout and to size the cooling system, as well as to support experimental campaigns in the definition of reduced-order thermal models to be implemented into the Battery Management System (BMS) for in-operation temperature prediction. The present work presents the development of a computational model of a 48V-20Ah 20-cell Li-ion module and its air-cooling system based on COMSOL Multiphysics software. Unlike most papers available in the literature, the individual cells are modelled by considering an internal ohmic heat generation term as a function of both state of charge, cell temperature and sign of the applied current (charge or discharge), exploiting experimentally validated data provided by the manufacturer in temperature-controlled conditions. In addition, the reversible thermal generation term due to entropic phenomena, which is often ignored in the literature, was computed alongside an irreversible term accounting for cell overpotentials. The entropic contribution, which was estimated experimentally and optimised computationally, resulted non-negligible when the module is cycled at ≤ 1C. To take into account the effect of the fan cooling system, the motion field was solved in COMSOL using a turbulent k-ε model. To ensure model accuracy, only minor geometrical simplifications were introduced to the fluid volume. The resulting geometrical complexity, made of manifold and narrow channels, called for special attention in the computational resolution. Assuming a decoupled behaviour, namely that the thermal evolution does not affect the flow field, allowed to use the stationary fluid-dynamic solution as the starting point for the time-dependent thermal simulation. The model was run under different experimental current profiles and the validation was performed on the entire module under effective operating conditions and not on a single cell under natural convection condition with the external environment, as is usually found in the literature. The computational data were found to be in good agreement with experimental measurements for all the cells even after charge-discharge cycles lasting more than two hours. The simulations provided insights to improve the positions of thermal sensors inside the module and to optimize the efficiency of the cooling system, that could not be done based on thermal measurements only. Figure 1

Experiment and Simulation for Air-Cooling the Tabs of a Pouch Battery Module with Distributed Resistance Model

Design and parametric optimization of thermal management of lithium-ion battery module with reciprocating air-flow

A parametric study on thermal management of an air-cooled lithium-ion battery module for plug-in hybrid electric vehicles

Thermal Management Optimization for Large-Format Lithium-Ion Battery Using Cell Cooling Coefficient

Effects of the different air cooling strategies on cooling performance of a lithium-ion battery module with baffle

A novel electro‐thermal coupled model of lithium‐ion pouch battery covering heat generation distribution and tab thermal behaviours

Experiment and simulation for pouch battery with silica cooling plates and copper mesh based air cooling thermal management system

Experimental Investigation on Pouch Lithium-ion Battery Thermal Management with Mini-Channels Cooling Plate Based on Heat Generation Characteristic

Analytical modeling and simulation of liquid cooling thermal management of a lithium-ion battery module

Numerical Simulation and Optimal Design of Air Cooling Heat Dissipation of Lithium-ion Battery Energy Storage Cabin

Thermo-electrochemical model for forced convection air cooling of a lithium-ion battery module

Study on heat dissipation structure of air-cooled Lithium ion battery module

Temperature Simulation and Analysis of Power Lithium-ion Battery Module Based on Two-dimensional CFD Thermal Model

Simulation of cooling plate effect on a battery module with different channel arrangement

Modelling Air Cooling in a Module of Prismatic Li-Ion Cells

Numerical Investigation of the Thermal Performance of a Hybrid Phase Change Material and Forced Air Cooling System for a Three-Cell Lithium-Ion Battery Module

Thermal investigation of lithium-ion battery module with different cell arrangement structures and forced air-cooling strategies

Modeling analysis on the cooling efficiency of composite phase change material-heat pipe coupling system in battery pack

Modeling and Analysis of Heat Dissipation for Liquid Cooling Lithium-Ion Batteries

Development of efficient air-cooling strategies for lithium-ion battery module based on empirical heat source model