Abstract:The effect of rolling temperature on the incomplete recrystallization behavior and the relationship to mechanical properties in 0.06C–4Mn-1.2Cr (wt.%) steel was investigated. Three plates of experimental steel were produced by hot rolling at different temperatures and intercritical annealing processes in this study. The microstructure of experimental steels was examined by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM). The mechanical properties of test steel were examined by impact test and tensile test. Austenite reversion and cementite precipitation-dissolution was numerically simulated under the assumption of local equilibrium. With the decrease of hot rolling temperature from 1000 °C to 800 °C, the uniform equiaxed prior austenite grains microstructures changed to heterogeneous microstructures of laminated and ultrafine prior austenite grains arranged alternatively. The tensile and impact tests revealed that the medium manganese steels rolling at 800 °C had an excellent combination of mechanical properties. Elongation had a great relationship with retained austenite fraction and stability. The fractography of impact specimens was examined to explore the toughening mechanism of the micro-laminated steels. The steel with uniform equiaxed grain structure exhibited a relatively low tensile strength of 750 MPa and low elongation of ∼20% and an extremely poor low-temperature toughness of ∼40 J at −40 °C. An enhanced low-temperature toughness (∼233 J at −40 °C), as well as an improved tensile strength (823 MPa) and higher elongation of ∼40%, was obtained in the steel with heterogeneous microstructures. The content of austenite in heterogeneous microstructure is twice that in uniform equiaxed grain structure. And cementite dissolved more thoroughly in the heterogeneous microstructure. The high austenite content of heterogeneous microstructures enabled the steel to be significantly stronger and ductile, which contributed to the high tensile strength and elongation to some extent. It is concluded that the effect of interface decohesion resulted in the occurrence of delamination. And the high austenite content and delamination greatly improved the low-temperature toughness of experimental steel.

Effects of Pre-Stretching on the Mechanical Behavior of Cold-Rolled 5%Mn Medium Manganese Steel

Effect of Deformed Prior Austenite Characteristics on Reverse Phase Transformation and Deformation Behavior of High-Strength Medium-Mn Steel

Effect of Mn content and strain rate on mechanical properties of high-C high-Mn austenitic steel

Effect of rolling temperature on microstructure and mechanical properties of medium manganese steel

Influence of manganese on deformation behavior of lightweight steel at different strain rate

Effect of a two-step annealing process on deformation-induced transformation mechanisms in cold-rolled medium manganese steel

Revealing the Role of Pre-Strain on the Microstructure and Mechanical Properties of a High-Mn Austenitic Steel

Material Enhancement Model for Austenitic Stainless Steel Sheets Subjected to Pre-stretching

Microstructural characteristics and tensile behavior of medium manganese steels with different manganese additions

Effect Of Strain Rate On The Deformation-Induced Martensite Transformation And Mechanical Behavior Of Austenitic Stainless Steels For Cold Stretched Pressure Vessels

Influence of cold rolling on the stability of retained austenite and mechanical properties of a Cu bearing low carbon low manganese steel

Effect of Pre-Stretch on the Precipitation Behavior and the Mechanical Properties of 2219 Al Alloy

Effect of Partition Temperature on Microstructure and Mechanical Properties of Cold‐Rolled Medium‐Manganese Steel

Strain Rate Sensitivity of Low‐Temperature Superplastic Heterogeneous Medium‐Mn Steel Fabricated by a Novel High‐Ratio Differential Speed Rolling

Improving the strength and ductility of medium Mn steel by depleting the stress-assisted martensite

Yielding Behavior and Strengthening Mechanisms of a High Strength Ultrafine‐Grained Cr–Mn–Ni–N Stainless Steel

Effect of hot/warm rolling on the microstructures and mechanical properties of medium-Mn steels

Microstructure evolution and tensile behaviour of a cold rolled 8 wt\% Mn medium manganese steel

Effect of Intercritical Annealing Time on Microstructure Evolution and Mechanical Properties of Low Carbon Medium Manganese Steel Subjected to Multi-Step Heat Treatment Process

Effect of pre-strain on mechanical properties and hardening behavior of TRIP steel

Effect of prestrain on tensile behavior of HS800 steel sheet