Abstract:Employing scaffolds containing cell-derived extracellular matrix (ECM) as an alternative strategy for the regeneration of bone defects has shown prominent advantages. Here, gelatin (Gel), sodium alginate (SA) and 58s bioactive glass (58sBG) were incorporated into deionized water to form ink, which was further fabricated into composite scaffolds by the 3D printing technique. Then, rat aortic endothelial cells (RAOECs) or rat bone mesenchymal stem cells (RBMSCs) were seeded on the scaffolds. After decellularization, two kinds of ECM-loaded scaffolds (RAOECs-ECM scaffold and RBMSCs-ECM scaffold) were obtained. The morphological characteristics of the scaffolds were assessed meticulously by scanning electron microscopy (SEM). In addition, the effects of scaffolds on the proliferation, adhesion, and osteogenic and angiogenic differentiation of RBMSCs were evaluated by Calcein AM staining and reverse transcription polymerase chain reaction (RT-PCR). In vivo, full-thickness bone defects with a diameter of 5 mm were made in the mandibles of Sprague-Dawley (SD) rats to assess the bone regeneration ability and biosafety of the scaffolds at 4, 8 and 16 weeks. The osteogenic and angiogenic potential of the scaffolds were investigated by microcomputed tomography (Micro-CT) and histological analysis. The biosafety of the scaffolds was evaluated by blood biochemical indices and histological staining of the liver, kidney and cerebrum. The results showed that the ECM-loaded scaffolds were successfully prepared, exhibiting interconnected pores and a gel-like ECM distributed on their surfaces. Consistently, in vitro experiments demonstrated that the scaffolds displayed favourable cytocompatibility. In vitro osteogenic differentiation studies showed that scaffolds coated with ECM could significantly increase the expression of osteogenic and angiogenic genes. In addition, the results from mandibular defect repair in vivo revealed that the ECM-loaded scaffolds effectively promoted the healing of bone defects when compared to the pure scaffold. Overall, these findings demonstrate that both RAOECs-ECM scaffold and RBMSCs-ECM scaffold can greatly enhance bone formation with good biocompatibility and thus have potential for clinical application in bone regeneration.

Preparing printable bacterial cellulose based gelatin gel to promote in vivo bone regeneration

Printability of hybridized composite from maleic acid-treated bacterial cellulose with gelatin for bone tissue regeneration

Constructing Osteo-Inductive Bio-Ink for 3D Printing Through Hybridization of Gelatin with Maleic Acid Modified Bacterial Cellulose by Regulating Addition Volumes of Maleic Acid Solution

Preparation and Characterization of Novel Bacterial Cellulose/Gelatin Scaffold for Tissue Regeneration Using Bacterial Cellulose Hydrogel

MXene reinforced microporous bacterial cellulose/sodium alginate dual crosslinked cryogel for bone tissue engineering

Fabrication of porous bone scaffolds using degradable and mouldable bacterial cellulose

Biofabrication of Natural Au/bacterial Cellulose Hydrogel for Bone Tissue Regeneration Via In-Situ Fermentation

In Vitro Cytotoxicity of Bacterial Cellulose Scaffolds Used for Tissue-engineered Bone

In situ shaping of intricated 3D bacterial cellulose constructs using sacrificial agarose and diverted oxygen inflow

Enhanced bone regeneration with bioprinted GelMA/Bentonite scaffolds inspired by bone matrix

Electrospun Gelatin/β-TCP Composite Nanofibers Enhance Osteogenic Differentiation of BMSCs Andin VivoBone Formation by Activating Ca2+-Sensing Receptor Signaling

Wood-based nanocellulose and bioactive glass modified gelatin–alginate bioinks for 3D bioprinting of bone cells

Fabrication and Evaluation of Alginate/Bacterial Cellulose Nanocrystals-Chitosan-Gelatin Composite Scaffolds

Three-Dimensional-Bioprinted Bioactive Glass/Cellulose Composite Scaffolds with Porous Structure towards Bone Tissue Engineering

Research on the osteogenesis and biosafety of ECM-Loaded 3D-Printed Gel/SA/58sBG scaffolds

Composite bioink incorporating cell-laden liver decellularized extracellular matrix for bioprinting of scaffolds for bone tissue engineering

Green Synthesized Magnesium Oxide Nanoparticles Reinforce Osteogenesis Properties of Bacterial Cellulose Scaffolds for Bone Tissue Engineering Applications: An In Vitro Assessment

Preparation and characterization of methacrylated gelatin/bacterial cellulose composite hydrogels for cartilage tissue engineering

Bioactive gelatin-sheets as novel biopapers to support prevascularization organized by laser-assisted bioprinting for bone tissue engineering

Printing bone in a gel: using nanocomposite bioink to print functionalised bone scaffolds

3D-printed mesoporous bioactive glass/GelMA biomimetic scaffolds for osteogenic/cementogenic differentiation of periodontal ligament cells