Abstract:The management of oily wastewater produced in the petrochemical industries poses an immense challenge from both practical and environmental points of view. Filtration using ceramic membranes has been considered a promising technology to remove stable emulsions from oily wastewater; however, the separation performances are severely limited by membrane fouling. In this study, we evaluated the filtration performance of porous ceramic membranes for the treatment of oil/water emulsions. Porous ceramic membrane, having different pore sizes (0.1–1.4 μm) and made from various materials (Al2O3, TiO2–ZrO2, TiO2, and SiC), were tested in a crossflow microfiltration system using oil/water emulsions. The emulsions were stabilized by anionic and cationic surfactants. The fouling caused by filtration is discussed in terms if membrane and emulsion properties. Pore size and surface charge were the two most important prominent fouling factors during the oil/water emulsion filtrations. For membranes with small pores, serious fouling was observed, irrespective of the type of surfactant; however, these membranes exhibited excellent oil rejection. The fouling was caused by the accumulation of oil droplets on the membrane surface, which subsequently led to the formation of a cake layer and/or a continuous oil layer. The effect of surface charge became significant regarding membranes of larger pore sizes, especially when membrane pore sizes were comparable to that of the droplet sizes. When the membrane and oil droplets had the same charge, electrostatic repulsion occurred, preventing the penetration of oil droplets into the pores. Although some of the small oil droplets could enter the pores, they would be trapped at the narrowing and/or flexing inside the pores because droplet deformation was inhibited by the electrostatic repulsion. Therefore, fouling occurred on the membrane surface and inside. As a result, a severe decline in water permeation was observed, together with a moderate oil rejection. By contrast, when the membrane and oil droplets were oppositely charged, oil droplets were deformed and entered the pores, resulting in permeation through the membrane. Therefore, water permeation was high, but oil rejection was sacrificed. These results indicate that both pore size and surface charge of membranes should be optimized to achieve better filtration performance.

The filterability of different types of minerals and the role of swelling clays in the filtration of oil sands tailings

The filtration of aqueous clay mineral suspension in the presence of bitumen

A review of the roles of constituent minerals and residual bitumen in the solid-liquid separation of oil sands tailings

Effects of mineral surface silanization and bitumen coating on its filtration from an aqueous slurry

The effect of clay type and solid wettability on bitumen extraction from Canadian oil sands

Effects of Hot Water-Based Extraction Process on the Removal of Petroleum Hydrocarbons from the Oil-Contaminated Soil

Evaluation of membrane fouling for in-line filtration of oil sands process-affected water: the effects of pretreatment conditions

Effects of different pretreatments on the performance of ceramic ultrafiltration membrane during the treatment of oil sands tailings pond recycle water: a pilot-scale study

Understanding the Properties of Bitumen Froth from Oil Sands Surface Mining and Treatment of Water-in-Oil Emulsions

Study on Oil Separation from Oil/Water Emulsion via Coagulation and Ultrafiltration

Optimal floc structure for effective dewatering of polymer treated oil sands tailings

Computational fluid dynamics investigation of bitumen residues in oil sands tailings transport in an industrial horizontal pipe

Effect of flyash addition to flocculation and freezing and thawing treatment on consolidation of oil sands fluid fine tailings

Molecular insights into oil detachment from hydrophobic quartz surfaces in clay-hosted nanopores during steam-surfactant co-injection

Filtration of surfactant-stabilized oil-in-water emulsions with porous ceramic membranes: Effects of membrane pore size and surface charge on fouling behavior

Detergency and its implications for oil emulsion sieving and separation

Simultaneously achieving high-effective oil-water separation and filter media regeneration by facile and highly hydrophobic sand coating

An Experimental on Filtration and Clogging of Geotextile Filters around Drain Pipes in Fine Tailings

Dewatering rate of vacuum tube filter (VTF)-system-treated sand–clay mixed slurry

3D-Printed Hierarchical Ceramic Architectures for Ultrafast Emulsion Treatment and Simultaneous Oil–Water Filtration

A novel hydrophobically-modified polyelectrolyte for enhanced dewatering of clay suspension