Abstract:Heavy metals constitute pollutants that are particularly common in air, water, and soil. They are present in both urban and rural environments, on land, and in marine ecosystems, where they cause serious environmental problems since they do not degrade easily, remain almost unchanged for long periods, and bioaccumulate. The detection and especially the quantification of metals require a systematic process. Regular monitoring is necessary because of seasonal variations in metal levels. Consequently, there is a significant need for rapid and low-cost metal determination methods. In this study, we compare and analytically validate absorption spectrometry with a sensitive voltammetric method, which uses a bismuth film-plated electrode surface and applies stripping voltammetry. Atomic absorption spectroscopy (AAS) represents a well-established analytical technique, while the applicability of anodic stripping voltammetry (ASV) in complicated sample matrices such as soil samples is currently unknown. This sample-handling challenge is investigated in the present study. The results show that the AAS and ASV methods were satisfactorily correlated and showed that the metal concentration in soils was lower than the limit values but with an increasing trend. Therefore, continuous monitoring of metal levels in the urban complex of a city is necessary and a matter of great importance. The limits of detection of cadmium (Cd) were lower when using the stripping voltammetry (SWASV) graphite furnace technique compared with those obtained with AAS when using the graphite furnace. However, when using flame atomic absorption spectroscopy (flame-AAS), the measurements tended to overestimate the concentration of Cd compared with the values found using SWASV. This highlights the differences in sensitivity and accuracy between these analytical methods for detecting Cd. The SWASV method has the advantage of being cheaper and faster, enabling the simultaneous determination of heavy elements across the range of concentrations that these elements can occur in Mediterranean soils. Additionally, a dsDNA biosensor is suggested for the discrimination of Cu(I) along with Cu(II) based on the oxidation peak of guanine, and adenine residues can be applied in the redox speciation analysis of copper in soil, which represents an issue of great importance.

Determination and assessment of contamination of toxic chemical elements in soils – Review

Determination and Risk Assessment of Toxic Chemical Elements in Fish Samples—A Review

Electrothermal Atomic Absorption Spectrometry to Determine As, Cd, Cr, Cu, Hg, and Pb in Soils and Sediments: A Review and Perspectives

Risk Assessment of Toxic Elements in Surface Soils Collected Near and Far from a Deactivated Lead Smelter in Bahia, Brazil

Assessing ecological risks and spatial distribution of potentially toxic elements in soils from anthropized environments in a watershed at the caatinga-Atlantic forest ecotone in Brazil

Agricultural management of an Oxisol affects accumulation of heavy metals

A multidisciplinary approach to assess history, environmental risks, and remediation feasability of soils contaminated by metallurgical activities. Part B: direct metal speciation in the solid phase

Background Concentrations and Quality Reference Values for Some Potentially Toxic Elements in Soils of São Paulo State, Brazil

Green tech soil analysis: a comparison of potentially toxic element contents among urban, agricultural, and gold mining areas in the Eastern Brazilian Amazon

Cadmium, Lead and Arsenic Contamination in an Abandoned Nonferrous Metal Smelting Site in Southern China: Chemical Speciation and Mobility.

Arsenic, lead, and cadmium bioaccessibility in contaminated soils: Measurements and validations

Source apportionment of metallic elements in urban atmospheric particulate matter and assessment of its water-soluble fraction toxicity

Toxic and heavy metals contamination assessment in soil and water to evaluate human health risk

Bismuth Film along with dsDNA-Modified Electrode Surfaces as Promising (bio)Sensors in the Analysis of Heavy Metals in Soils

A simple method based on ICP-MS for estimation of background levels of arsenic, cadmium, copper, manganese, nickel, lead, and selenium in blood of the Brazilian population

Assessment of groundwater quality from monitoring wells in an area occupied by a cemetery in South Brazil

Comparison of ultrasound-assisted extraction, slurry sampling and microwave-assisted digestion for cadmium, copper and lead determination in biological and sediment samples by electrothermal atomic absorption spectrometry

Heavy metals in soils derived from sedimentary rocks of the Gurgueia River watershed, Northeast, Brazil: background values, distribution and ecological risk assessment

Heavy Metals in Contaminated Soils: A Review of Sources, Chemistry, Risks and Best Available Strategies for Remediation

Sources, Indicators, and Assessment of Soil Contamination by Potentially Toxic Metals

Fractionation of trace elements in agricultural soils using ultrasound assisted sequential extraction prior to inductively coupled plasma mass spectrometric determination