Abstract:Two-phase flows are common phenomena in numerous industrial equipment. The complex and changeable phase interface determines the characteristics such as flow pattern evolution and energy-mass transport between the two phases. As a key component of rod bundle fuel assembly in nuclear reactors, the spacer grid plays important roles, including fixing the rod position, promoting mixing, and intensifying heat transfer. This study investigated the axial two-phase flow evolution and interfacial area transport characteristics downstream of the non-mixing vane spacer grid (N-MVSG) inside a tight lattice rod bundle fuel assembly under air-water two-phase flows. A self-developed double-layer wire-mesh sensor (WMS) was adopted to survey 6 positions downstream of the N-MVSG ( Z / D h = 9.15, 14.94, 20.73, 26.52, 32.31, and 61.26), and 42 cases were acquired from bubbly to cap-bubbly and to slug flow. Eventually, void fraction, bubble velocity, interfacial area concentration (IAC), and bubble size distribution (BSD) databases were established. Under the group-1 (G-1) flow, some small bubbles migrate toward the subchannel center, and the void fraction gap-region peak distribution gets weakened. The 1-D void fraction and IAC after the N-MVSG increase first and then gradually recover to its upstream level. Under the two-group flow, the N-MVSG clearly cut group-2 (G-2) bubbles, and the time-averaged void fraction profile downstream of N-MVSG undergoes the evolution of the square distribution, and ring distribution, and then reverts to the upstream core peak distribution. The analysis of BSD results indicates that the G-2 bubbles' break-up is mainly caused by the increment of the flow-field turbulence, rather than the cutting of the N-MVSG. The 1-D void fraction and IAC transport show the total void fraction and IAC increase first and then recover downstream of the N-MVSG. Meanwhile, the G-2 void fraction and IAC reach the maximum before the G-1's due to the coalescence of the G-1 and G-2 bubbles at the N-MVSG's exit. The model evaluation using the IATE without bubble interaction source/sink terms shows that, for most cases, the advection effect and pressure effect dominate the void fraction and IAC evolution. The remarkable bubbles' break-up occurs under the transition cases and the two-group cases with high liquid velocity. In future studies, the additional source/sink term models considering the N-MVSG effect should be developed based on these cases to improve the IATE prediction performance.

Particle image velocimetry measurements of transition flows in an 84-pin hexagonal rod bundle with spacer grids

Flow field characteristics of a 127-pin rod bundle with hexagonal spacer grids

Experimental Study of Flow Structures in a Large Range Downstream the Spacer Grid in a 5 × 5 Rod Bundle Using TR-PIV

Effects of Rectangular-Type Spacer on Hert Transfer and Flow in Coolant Passage.

PIV measurements for VVER pressurized water reactor rod bundle geometries including spacer grids for CFD model validations

Large eddy simulation of a turbulent flow in a 5 x 5 rod bundle with a mixing vane spacer grid

Large-eddy simulations of turbulent flow for grid-to-rod fretting in nuclear reactors

Scale-resolving simulations of the flow in a nuclear fuel bundle with a channel spacer grid using partially averaged Navier–Stokes and large-eddy simulation

Of annular two-phase flow on rod-bundle geometry with spacer

General flow sweeping mixing model for subchannel analysis and application to three rod bundles with different typical spacer methods

Two-phase flow evolution and interfacial area transport downstream of the non-mixing vane spacer grid in rod bundle channels

Numerically simulating the thermal–hydraulic characteristics within the fuel rod bundle using CFD methodology

Modulation of flow meandering in the gap of a model of a peripheral subchannel of a fuel rod assembly

Flow Characteristics within an Interior Subchannel of a 61-pin Wire-Wrapped Hexagonal Rod Bundle with a Porous Blockage

Numerical investigations of flow in nuclear fuel assembly with spacer grid and OpenFOAM validation

Summary: Study on Wavy Interface Behavior and Droplet Entrainment of Annular Two-Phase Flow in Rod Bundle Geometry with Spacers

Fundamental study of heat transfer and flow situation around a spacer (in the case of a cylindrical rod as a spacer)

Implementation of a Spacer Grid Rod Thermal-Hydraulic Reconstruction (ROTHCON) Capability into the Thermal-Hydraulic Subchannel Code CTF

PIV and CFD Study on Crossflow Characteristics in a 7-Pin Wire-Wrapped Bundle Channel

Cfd Investigating the Effects of Different Mixing Vane Designs on the Localized Thermal-Hydraulic Characteristics in the Rod Bundles with Grid Spacer

Flow mixing and heat transfer deterioration investigation of supercritical carbon dioxide in wire-wrapped bundles