Abstract:Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, Ahead of Print. Cranial defects are often caused by trauma, diseases or malignancy. To repair such defects, skull reconstruction or cranial implants are required for protecting intracranial structures and normalizing cerebral hemodynamics. To relieve Intracranial Pressure (ICP) surgeons restore cranial defects using the preserved bone of a patient. In case of non-availability of natural bone cranial implants are fabricated using biocompatible materials including Titanium Alloys (Ti-6Al-4V) and polyether-ether-ketone (PEEK). Patient-specific implants (PSI) manufactured using 3D printing, 3D imaging technologies and 3D modeling software, are preferred over conventional manufacturing methods. During cranial fixation bone fragments, grafts and bone flaps are fixed to the cranium to offer stable closure in surgery. Effective attachment of an implant to a defective skull is influenced by the joints and fixture arrangements at the interface. These fixtures can have various designs, materials and joining procedures. PEEK behaves similarly to bone during deformation, which means it is receptive to titanium fixations and supports soft tissue adhesion due to its inert nature. This study considers PEEK as an implant material for reconstructing a bone-defected skull with Ti-6Al-4V fixtures attached at the skull-implant interface. This work compares Ti-6Al-4V fixture shapes (Linear, Square and Burrhole) with different orientation angles and topologies ('+' and 'X') attached to PEEK cranial implants of variable thicknesses (1–7 mm). Using Finite Element Method (FEM)/Finite Element Analysis (FEA), von Mises stress analysis was analyzed to identify the implant thicknesses that would bear an external load of 1780 N and ICP of 15 mmHg without failure. With a yielding limit of 100 MPa for PEEK, all proposed design arrangements for the fixture plates in the skull-implant assembly were well within these limits exhibiting a maximum von Mises stress of 51.985 MPa for the least implant thickness of 1 mm and weight 12.90 g. Considering all the designs, a Linear Fixture shape with 45° angular orientations placed in 'X' topology exhibited least stress of 18.477 MPa and was therefore proposed as the most optimized design for the skull-implant fixture assembly. Selection of an optimized design arrangement is also dependent upon other clinical factors, such as number of screws used, the Additive Manufacturing (AM) technique for fabricating/cutting of precise slots within the implant. The skull and flexibility of the fixture plates are also considered in relation to the required operating theatre time and skills of the surgical team.

Applications of Polyetheretherketone in Trauma, Arthroscopy, and Cranial Defect Repair

Medical Applications of Polyether Ether Ketone

Polyetheretherketone development in bone tissue engineering and orthopedic surgery

Designing cranial fixture shapes and topologies for optimizing PEEK implant thickness in cranioplasty

Carbon fiber reinforced PEEK Optima--a composite material biomechanical properties and wear/debris characteristics of CF-PEEK composites for orthopedic trauma implants

Poly-Ether-Ether-Ketone (PEEK) Biomaterials and Composites: Challenges, Progress, and Opportunities

Polyether-Ether-Ketone (PEEK) and Its 3D-Printed Quantitate Assessment in Cranial Reconstruction

PEEK (Polyether-ether-ketone) and its composite materials in orthopedic implantation

Surface modification of PEEK implants for craniofacial reconstruction and aesthetic augmentation—fiction or reality?

Developments of PEEK (Polyetheretherketone) as a biomedical material: A focused review

Behavior of polyether-ether-ketone (PEEK) in prostheses on dental implants. A review

Research Progress of Polyether Ether Ketone and Its Composites in Orthopedic Trauma Implants

Modification of polyether ether ketone for the repairing of bone defects

Bone Regeneration and Polyetheretherketone Implants in Maxillo-Facial Surgery and Neurosurgery: A Multidisciplinary Study

Optimization and manufacture of polyetheretherketone patient specific cranial implants by material extrusion - A clinical perspective

State‐of‐the‐art review on the high‐performance poly (ether ether ketone) composites for mechanical, tribological and bioactive characteristics

Additive manufactured polyether-ether-ketone implants for orthopaedic applications: a narrative review.

Additively manufactured polyether ether ketone (PEEK) skull implant as an alternative to titanium mesh in cranioplasty

Quantitative Assessment of Point-of-Care 3D-Printed Patient-Specific Polyetheretherketone (PEEK) Cranial Implants

Areas for use of PEEK material in dentistry

Polyetheretherketone Implant Cranioplasty for Large Cranial Defects: A Seven-Year Follow-Up