Abstract:The advanced and comprehensive utilization and entire burning prohibition of fully covered crop straw in farmlands have become significant in modern agriculture. Considering the high straw-returning yields, complicated operating procedures, and tight crop-stubble rotation, as well as high power consumption, poor smoothness shun, and low multiple-seed index obtained using traditional compound operation machines for rice and wheat rotation regions in the middle and lower reaches of the Yangtze River, this study extends the concept of the new 'clean-area planting' pattern. A minimum-tillage planter with straw smashing and strip laying was developed for full straw mulching fields. In a single pass, the planter could complete multiple operation processes, including straw-stubble smashing, seed-belt cleaning, inter-row stacking, seed-bed treatment, fertilization sowing, and soil covering and suppression. A mechanical model for the straw particle was established using the discrete element method (DEM) and EDEM software, and DEM virtual simulation tests and numerical analysis were conducted. A quadratic rotating orthogonal center combination test was implemented by setting the smashing spindle speed n′(A), machine ground speed v(B), and rotation tilling spindle speed n(C) as the influence factors, with the straw mulch uniformity ε1 and the coefficient of straw ridge disturbance ε2 as the evaluation indices. Response surface optimization analysis was performed to obtain the optimal combination of operational parameters affecting the planter working performance. The results indicated that the most significant factors affecting the straw mulch uniformity, ε1, and coefficient of straw ridge disturbance, ε2, were: smashing spindle speed, n′, > machine ground speed, v, > rotation tilling spindle speed, n, and rotation tilling spindle speed, n, > machine ground speed, v, > smashing spindle speed, n′. The optimal combination of these operational parameters was n′ = 2042.35 r/min, v = 0.99 m/s, and n = 440.93 r/min, providing a maximum ε1 = 94.30% and minimum ε2 = 9.67%. Field verification test results indicated that the optimized minimum-tillage planter achieved mean values of ε1 = 86.25% and ε2 = 9.75%, with average relative errors of 8.51% and 10.27% compared to the simulation tests, respectively. The accuracy and effectiveness of the DEM simulation model were verified. Moreover, the stipulated industry standards and operation requirements of no-tillage planter machinery with a straw-returning field can be satisfied, and technical support can be provided for follow-up studies of similar conservation tillage equipment.

Control method of seedbed compactness based on fragment soil compaction dynamic characteristics

Simulation of Front End Loader Bucket–soil Interaction Using Discrete Element Method

Earth Pressure Balance Control Based on Feedforward-Feedback Compound Control

Quasi-static analysis for quantitative estimation of improvement effect of cohesionless soil treated by dynamic compaction

Simulation and Analysis of the Working Process of Soil Covering and Compacting of Precision Seeding Units Based on the Coupling Model of DEM with MBD

Simulation of canola seedling emergence dynamics under different soil compaction levels using the discrete element method (DEM)

Prediction of cutting forces and soil behavior with discrete element simulation

Quantification of the Soil Stiffness Constants Using Physical Properties of Paddy Soils in Yangtze Delta Plain, China

Three-dimensional Numerical Simulation of Dynamic Compaction of Backfilled Soil

RESEARCH ON THE SEEDING DEPTH ADJUSTMENT DEVICE BASED ON THE TIP OF FURROW OPENER FORCE MEASUREMENT

Compaction Quality Evaluation of Subgrade Based on Soil Characteristics Assessment Using Machine Learning

Establishment and Parameter Calibration of a Simulation Model of Coated Cotton Seeds and Soil

Co-simulation for optimal working parameter selection during soil vibratory compaction process

Simulation of Dynamic Compaction and Analysis of Its Efficiency with the Material Point Method

Calibrating contact parameters of typical rotary tillage components cutting soil based on different simulation methods

A Tillage Depth Monitoring and Control System for the Independent Adjustment of Each Subsoiling Shovel

High performance prediction of soil compaction parameters using multi expression programming

Numerical simulation and field tests of minimum-tillage planter with straw smashing and strip laying based on EDEM software

Modeling the interaction of soil and a vibrating subsoiler using the discrete element method

PZT-Based Soil Compactness Measuring Sheet Using Electromechanical Impedance