Abstract:To tackle the challenges raised by climate change, we need to rapidly switch our energy sources to low-carbon ones for all economic sectors. As renewable energies are intermittent, efficient energy carriers, such as hydrogen, will be needed to meet the energy demand. Green hydrogen is considered to be a promising energy vector for the future. However, in addition to problematics related to its production, safe and large scale storage solutions still need to be developed. The geological formations including saline aquifers and former depleted gas fields offer the largest storage capacities but are more adapted to seasonal or mid-to-long term storage. Conversely, underground salt caverns are well suited for storage/withdrawal cycles as short as daily cycling. These artificial structures, offering exceptional tightness, have already been used for decades for hydrocarbons storage but at seasonal storage/withdrawal cycles. The adaptation to short-term hydrogen storage still requires further studies to ensure the stability of the caverns under such loading conditions. Indeed, rapid cyclic loading conditions may impact the tightness and the integrity of the cavern [1, 6]. Rock salt is polycrystalline material with an essentially viscoplastic behaviour, involving different micro-mechanisms such as crystal slip plasticity and grain boundary sliding. At mechanical loading conditions representative of those operated in storage caverns, the rock salt is characterized by non-linear viscous flow. The activation of grain boundary sliding is necessary to accommodate local plastic incompatibilities between neighbouring grains. It has been shown in uniaxial loading conditions but has not been verified in triaxial conditions yet [2, 4]. The presence of brine also affects the micro-mechanisms involved, with for example phenomena like dissolution-precipitation or diffusional mass transfer along grain boundaries, and can modify the mechanical behaviour [5]. In our studies, we investigate the active micro-mechanisms in synthetic halite through in situ X-ray microcomputed tomography (XR-μCT) analysis and digital volume correlation (DVC) and damage quantification. To reproduce loading conditions representative of those in real salt caverns, we apply different confining pressures with a triaxial cell. This triaxial device, developed recently [3], is adapted to in situ XR-μCT tests. We study the development of damage networks and the evolution of pores during the deformation of rock salt under different confining pressures. Samples of halite are prepared by compaction of pure NaCl powder in dry and humid conditions. It gives samples with different brine contents and allows us to study the effect of brine on the deformation mechanims. An effect of brine is visible, as the cracks seem to appear earlier in the dry samples. On the μCT scans, cracks start to be visible for a lower strain in the case of dry samples compared to the case of wet samples. For a dry sample in uniaxial loading conditions, the cracks were already clearly visible and well formed in most of the sample at 1.3% axial strain. For a wet sample, very few cracks only start to become slightly visible in some areas at 1.45% axial strain. This could be due to the activity of mechanisms involving brine, such as dissolution-precipitation allowing for crack healing. The effect of the confining pressure is also noticeable. After unloading the wet sample and removing the confining pressure, we observed that the few cracks formed during the deformation of the sample opened up, indicating that the healing process was not complete. Dissolution and precipitation are kinetically slaw processes, which are mostly active at low strain rates. Therefore, further deformation experiments must also explore the effect of strain rate. Natural salt always contains some humidity. Therefore, the effect of brine in deformation and damage formation/healing mechanisms is important to understand, especially in the context of gas storage in salt caverns.

Failure transition of shear-to-dilation band of rock salt under triaxial stresses

Analysis of damage characteristics and energy evolution of salt rock under triaxial cyclic loading and unloading

Experiments on Mechanical Properties of Salt Rocks under Cyclic Loading

The Mechanical Properties of Rock Salt under Cyclic Loading-Unloading Experiments

3D microscale investigation of active deformation mechanisms of halite under conditions representative of underground hydrogen storage

Creep–fatigue Mechanical Characteristics of Salt Rocks under Triaxial Loading: an Experimental Study

Investigation on the Deformation and Strength Characteristics of Rock Salt under Different Confining Pressures

Failure Mechanism of Bedded Salt Formations Surrounding Salt Caverns for Underground Gas Storage

Damage evaluation of rock salt under multilevel cyclic loading with constant stress intervals using AE monitoring and CT scanning

Empirical analysis of unloading creep damage mechanism of salt rock at 110 °C

Damage evolution of rock salt under cyclic loading in unixial tests

Acoustic emission characteristics of rock salt under multi-stage cyclic loading

Damage Evolution of Rock Salt under Multilevel Amplitude Creep–fatigue Loading with Acoustic Emission Monitoring

Long-term Deformation of Rock Salt under Creep–fatigue Stress Loading Paths: Modeling and Prediction

Damage Evolution Characteristics of Rock Salt under Different Stress Conditions

A New Testing Method for the Characterization of the Tension-Compression Cyclic Behavior of Rock Salt

Experimental Study Of Triaxial Interval Fatigue Of Salt Rock

Experimental study of mechanical and hydraulic properties of bedded rock salt from the Jintan location

Acoustic Emission Characteristics and Energy Evolution of Salt Rock for Deep-Salt-cavern Engineering under Triaxial Loading and Unloading

Creep-fatigue characteristics of rock salt under different loading paths

Comparison of the Characteristics of Rock Salt Exposed to Loading and Unloading of Confining Pressures