Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Enhancing Catalytic Conversion of Polysulfides by Hollow Bimetallic Oxide-Based Heterostructure Nanocages for Lithium-Sulfur Batteries

A Nitrogen/Oxygen Dual-Doped Porous Carbon with High Catalytic Conversion Ability Toward Polysulfides for Advanced Lithium–Sulfur Batteries

Palladium nanocrystals-imbedded mesoporous hollow carbon spheres with enhanced electrochemical kinetics for high performance lithium sulfur batteries

Construction of Binary Metal Sulfide Nanoparticles to Boost Catalytic Activity for Lithium-Sulfur Batteries

Bimetallic Nanoparticles Decorated Porous Carbon As the Host Material to Enhance the Performance of Lithium-Sulfur Batteries

Surface-coated AlF3 Nanolayers Enable Polysulfide Confinement Within Biomass-Derived Nitrogen-Doped Hierarchical Porous Carbon Microspheres for Improved Lithium-Sulfur Batteries

Coordinated Immobilization and Rapid Conversion of Polysulfide Enabled by a Hollow Metal Oxide/Sulfide/Nitrogen‐Doped Carbon Heterostructure for Long‐Cycle‐Life Lithium‐Sulfur Batteries

A hollow Co0.12Ni1.88S2/NiO heterostructure that synergistically facilitates lithium polysulfide adsorption and conversion for lithium-sulfur batteries

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries

Enhanced Polysulfide Regulation <i>via</i> Porous Catalytic V<sub>2</sub>O<sub>3</sub>/V<sub>8</sub>C<sub>7</sub> Heterostructures Derived from Metal-Organic Frameworks toward High-Performance Li-S Batteries

Hollow CoP-FeP cubes decorating carbon nanotubes heterostructural electrocatalyst for enhancing the bidirectional conversion of polysulfides in advanced lithium-sulfur batteries

Hollow and Porous N‐Doped Carbon Framework as Lithium‐Sulfur Battery Interlayer for Accelerating Polysulfide Redox Kinetics

Hollow Co-Fe LDH as an effective adsorption/catalytic bifunctional sulfur host for high-performance Lithium–Sulfur batteries

Coupling highly dispersed Sb2S3 nanodots with nitrogen/sulfur dual-doped porous carbon nanosheets for efficient immobilization and catalysis of polysulfides conversion

Dual-heterostructures decorated interweaved carbon nanofibers sulfur host for high performance lithium-sulfur batteries

Synergistic effect of selectively etched CoFe and N-doped hollow carbon spheres for high performance lithium-sulfur batteries

Boosting Polysulfide Catalytic Conversion and Facilitating Li+ Transportation by Ion‐Selective COFs Composite Nanowire for LiS Batteries

Heterostructured Mn3O4‐MnS Multi‐Shelled Hollow Spheres for Enhanced Polysulfide Regulation in Lithium–Sulfur Batteries

Atomic-Level Catalyst Coupled with Metal Oxide Heterostructure for Promoting Kinetics of Lithium-Sulfur Batteries

A Porous Hexagonal Prism Shaped C-In2-XCoXO3 Electrocatalyst to Expedite Bidirectional Polysulfide Redox in Li-S Batteries

Porous Fe2O3 Doped Cathodes for Lithium-Sulfur Batteries