Abstract:The complex chemical structure of polypeptide and the imperfection of processing technology cause the mechanical properties of regenerated keratin to be hard and brittle. This defect seriously affects the application prospects of keratin materials. To solve the above problems, α-lipoic acid modified keratin (KER) was blended with Polyamide 6 (PA6) and prepared into composite fibers via the wet-spinning method in this work. The spinnability and spinning conditions of the KER/PA6 blend solution were analyzed by rheological theory. The results illustrated that keratin solution will easily form a gel state under certain temperatures and concentrations, which was not conducive to the preparation of regenerated fiber. When the temperature was 45 °C and the mass fraction was 10 %, the viscosity and rheology of the solution were appropriate. The rheological properties of the blend solution showed that too much keratin would make the solution easy to gel, which was not conducive to the preparation of regenerated fibers and may affect the fiber properties. On this basis, the prepared composite fibers were characterized to explore the macromolecular aggregation state of keratin and PA6 in fibers. FT-IR and XRD results proved that there was no chemical reaction between keratin and PA6 in the composite fibers, which belonged to physical blending. At the same time, the two polymers had good compatibility and can be blended at the molecular level. SEM, DSC, and tensile strength test results indicated that when the proportion of keratin was too high, the structure and properties of the composite fibers will have obvious defects, which was consistent with the rheological analysis. Therefore, the blend ratio of keratin/PA6 was determined to be 3:7. Under this condition, the fibers exhibited a homogeneous structure and good thermal properties, especially its mechanical properties were close to wool fibers. The KER/PA6 composite fibers show important research value and can also provide technical reference for the development of regenerated biomass materials.

Fabrication of mechanical robust keratin film by mesoscopic molecular network reconstruction and its performance for dye removal

Fabrication of mechanical robust keratin adsorbent by induced molecular network transition and its dye adsorption performance

Functional porous Ce-UiO-66 MOF@Keratin composites for the efficient adsorption of trypan blue dye from wastewater: A step towards practical implementations

Producing bacterial nano-cellulose and keratin from wastes to synthesize keratin/cellulose nanobiocomposite for removal of dyes and heavy metal ions from waters and wastewaters

Adsorption of methylene blue dye on feather keratin/silk fibroin porous aerogels

Reusable kaolin impregnated aminated chitosan composite beads for efficient removal of Congo red dye: isotherms, kinetics and thermodynamics studies

Wool-derived keratin nanofiber membranes for dynamic adsorption of heavy-metal ions from aqueous solutions

Fabrication of PHBV/keratin composite nanofibrous mats for biomedical applications

Regenerated Silk Nanofibers for Robust and Cyclic Adsorption–Desorption on Anionic Dyes

Bioinspired Robust Keratin Hydrogels for Biomedical Applications

Versatile Keratin Fibrous Adsorbents with Rapid-Response Shape-Memory Features for Sustainable Water Remediation

Wool keratin as a novel, alternative, low-cost adsorbent rich in various –N and –S proteins for eliminating methylene blue from water

Green Nanoengineered Keratin Derived Bio‐Adsorbent for Heavy Metals Removal from Aqueous Media

Hierarchical porous ceramic adsorbents with nanofibrous-granular composite structure for efficient dye removal

Investigation of Keratin/Poly(ethylene oxide) Nanofiber Membrane Prepared with Different Post-crosslinking Method

A facile and eco-friendly approach for preparation of microkeratin and nanokeratin by ultrasound-assisted enzymatic hydrolysis

Alternating spin-and-spray electrospun scaffold membranes with fractionated MIL-101(Cr) adsorbent for high-performance single-pass dye adsorption process

Preparation of Ag Doped Keratin/PA6 Nanofiber Membrane with Enhanced Air Filtration and Antimicrobial Properties

Characterization of the keratin/polyamide 6 composite fiber's structure and performance prepared by the optimized spinning process based on the rheological analysis

Self-assembled electrospun PVA/CMC/PEO composite fiber film material with enhanced dye adsorption performance for wastewater treatment

Preparation of Reusable Porous Carbon Nanofibers from Oxidized Coal Liquefaction Residue for Efficient Adsorption in Water Treatment