Conceptual Design of Layered Distributed Propulsion System to Improve Power-Saving Benefit of Boundary-Layer Ingestion

Zhiping Li,Yujiang Lu,Tianyu Pan

DOI: https://doi.org/10.3390/aerospace11020141

IF: 2.66

2024-02-09

Aerospace

Abstract:DPS (distributed propulsion system) utilizing BLI (boundary-layer ingestion) has shown great potential for reducing the power consumption of sustainable AAM (advanced air mobility), such as BWB (blended-wing body) aircraft. However, the ingesting boundary layer makes it easier for flow separation to occur within the S-shaped duct, and the consequent distortion due to flow separation can dramatically reduce the aerodynamic performance of the fan, which offsets the power-saving benefit of BLI. By analyzing the source of power saving and power loss of BLI, this paper presents the LDPS (layered distributed propulsion system) concept, in which the freestream flow and boundary-layer flow are ingested separately to improve the power-saving benefit of BLI. In order to preliminarily verify the feasibility of LDPS, an existing DPS is modified. The design parameters and the system performances of LDPS are studied using a 1D engine model. The results show that there is an optimal ratio of the FPR (fan pressure ratio) for the FSE (freestream engine) to the BLE (boundary-layer engine) that maximizes the PSC (power-saving coefficient) of LDPS. This optimal ratio of FPR for the two fans can be obtained when the exit velocities of FSE and BLE are the same. Under the optimal ratio of FPR for the two fans, the PSC of LDPS is improved by 5.83% compared to conventional DPS.

engineering, aerospace

What problem does this paper attempt to address?

The paper primarily focuses on the application of Boundary-Layer Ingestion (BLI) technology in Distributed Propulsion Systems (DPS) for Advanced Air Mobility (AAM) vehicles, such as Blended-Wing Body (BWB) aircraft. Although BLI technology can reduce the power consumption of propulsion systems, it also brings some negative effects, such as flow separation in S-shaped inlets, leading to reduced intake pressure recovery and airflow distortion, which in turn affects fan efficiency. To address these issues, the paper proposes the concept of a Layered Distributed Propulsion System (LDPS). The design of LDPS aims to maximize the energy-saving benefits brought by BLI by separating the ingestion of free-stream and boundary-layer flows, thereby reducing the performance loss caused by their mixing. Specifically, the paper first reviews the physical principles of BLI and analyzes the sources of power savings in traditional BLI propulsion systems as well as the power losses caused by airflow distortion. Then, the paper introduces the concept of LDPS, which includes two rows of propulsion systems arranged along the wingspan: the row closer to the body ingests boundary-layer flow (referred to as Boundary-Layer Engine, BLE), while the upper row ingests free-stream flow (referred to as Free-Stream Engine, FSE). This arrangement ensures that the quality of the free-stream flow is not affected by the boundary-layer flow, and the boundary-layer flow is organized to minimize internal flow losses. By using a one-dimensional engine model to modify an existing DPS, the design parameters and system performance of LDPS were studied. The results show that, under the optimal fan pressure ratio configuration, the energy-saving coefficient of LDPS is 5.83% higher compared to traditional DPS. In summary, this paper aims to explore a new method to optimize BLI propulsion systems through the design and preliminary validation of the LDPS concept, in order to improve their energy-saving effects in future large AAM vehicles such as BWB.

Conceptual Design of Layered Distributed Propulsion System to Improve Power-Saving Benefit of Boundary-Layer Ingestion

System Level Study of Light Sport Aircraft with Conventional and Unconventional Propulsion Systems

Potential for Energy Recovery from Boundary-Layer Ingesting Actuator Disk Propulsion

Aerodynamic Shape Optimization of an Aircraft Propulsor Air Intake with Boundary Layer Ingestion

Conceptual Design and Optimization of Distributed Electric Propulsion General Aviation Aircraft

Blade Redesign Based on Secondary Flow Suppression to Improve Energy Efficiency of a Centrifugal Pump

A Conceptual Design and Optimization Approach for Distributed Electric Propulsion eVTOL Aircraft Based on Ducted-Fan Wing Unit

Distributed Hybrid Electric Propulsion Aircraft Design Based on Convex Optimized Power Allocation Management

Bi-layer sizing and design optimization method of propulsion system for electric vertical takeoff and landing aircraft

Blade Thickness Redesign to Improve Efficiency and Decrease Unsteady Pressure Pulsation of a Low Specific Speed Centrifugal Pump

Deep Learning Based Adaptive Deformation of Aerodynamic Shape for Ducted Propellers

Deep Learning Based Fast Prediction and Optimization of Aerodynamic Performance for a Propeller with Gurney Flap

Design Optimization of the Last Stage of a 4.5-Stage Compressor Using a POD-based Hybrid Model

Performance of flapping airfoil propulsion with LBM method and DMD analysis

Hybrid Aerodynamic Optimization of a Propeller Based on the Reformulated Blade Element Momentum Theory

Optimization Design and Propulsion System Sizing Methodology of Double‐Layer Staggered Octocopter

Rapid Design Method of Heavy-Loaded Propeller for Distributed Electric Propulsion Aircraft

Hovering efficiency optimization of the ducted propeller with weight penalty taken into account

Friction drag reduction based on a proportional-derivative control scheme

Parameterization investigation on distributed electric propulsion aircraft aerodynamic characteristics

Optimization of Impeller Structure Parameters of a Centrifugal Fan in a Powered Air-Purifying Respirator Power System