Determination of the Grinding Area and Allowance in the Radome Grinding
DM Guo,MJ Liu,RK Kang,JM Liu
DOI: https://doi.org/10.4028/www.scientific.net/kem.259-260.174
2004-01-01
Key Engineering Materials
Abstract:The radome is often used to house the airborne scanning radar antennas. The radomes electric thickness, which is dependent on the geometric thickness and the permittivity, may not meet the design requirement after semi-finished machining. It will lead to a large boresight error of the radar antenna. One way to decrease the boresight error induced by radome is to compensate the electric thickness error by modifying the geometric thickness of the radome. In practice, only the inner surface of the radome can be precisely modified by a special grinding machine after the outer surface has been finished. But how to determine the grinding area and the grinding allowance from the boresight error is a very complicated reverse engineering problem, which is hardly solved by pure mathematical method. A new method combining the numerical calculation and the practical measurement to determine the grinding area and allowance is presented in this paper. It is shown that this method is simple and practical, being applicable for many kinds of radomes. Introduction The radome is often used to house the airborne scanning radar antennas. The radome withstands great aerodynamic and thermodynamic loads, preventing the antenna homing head from external interference in the flying. Furthermore, the radome should not decrease the homing performance of the radar antenna [1]. At present, although the geometric shape and dimension of the radome after semi-finished machining can satisfy the aerodynamics demand, the radomes electric thickness, which depends on the geometric thickness and the permittivity and influence the boresight accuracy, may not meet the design requirement, leading to a larger boresight error of the radar antenna [1]. Through analyzing the relationships between the electric thickness, the geometric thickness and the permittivity of the radome [2], it is known that one way to decrease the boresight error induced by radome is to compensate the electric thickness error by modifying the geometric thickness of the radome. In practice, only the inner surface of the radome can be precisely modified by applying a special grinding machine after the outer surface has been finished. How to determine the grinding area and allowance from the boresight error is a very complicated reverse engineering problem, which is hardly solved by pure mathematical method. A new method combining the numerical calculation and the practical measurement to determine the grinding area and allowance will be presented in this paper. Calculation of the Boresight Error The boresight error is defined as the angular deviation of the electrical boresight of an antenna from its reference boresight. The boresight error is induced by asymmetry in structure and electricity of the radome relative to the antenna aperture. The boresight error gravely influences the homing accuracy and so, it must be restricted within a definite limit. Therefore, it is necessary to precisely calculate the boresight error by means of numerical method. The boresight error is determined by the far-fields pattern of the antenna-radome system that will be analyzed in the following. First of all, the numerical description of the inner surface of the radome must be determined. In this paper, a bicubic B-spline is applied to represent the inner surface of the radome due to its fine local Key Engineering Materials Online: 2004-03-15 ISSN: 1662-9795, Vols. 259-260, pp 174-179 doi:10.4028/www.scientific.net/KEM.259-260.174 © 2004 Trans Tech Publications Ltd, Switzerland All rights reserved. No part of contents of this paper may be reproduced or transmitted in any form or by any means without the written permission of Trans Tech Publications Ltd, www.scientific.net. (Semanticscholar.org-13/03/20,19:03:38) Journal Title and Volume Number (to be inserted by the publisher) 175 quality [3-4]. Analysis of the Far-fields Pattern of the Antenna-radome System by Means of PWS-SI Method. There are many ways to analyze the far-fields pattern of the antenna-radome system, such as the ray tracing method, the plane wave spectrum (PWS) method, the edge diffraction method and the aperture-integration, etc. The ray tracing method is applied for analysis of the lager antenna. For this kind of antenna, whose aperture area is generally less than 75 2 ( is the electromagnetic wave wavelength), PWS-SI technique is suitable. The plane wave spectrum-surface integration (PWS-SI) method [5-8] is a practical method for analyzing the antenna-radome system. This method can accurately analyze and predict the electromagnetic properties of a smaller three-dimensional antenna -radome system. The basic idea of this method is based on the induction equivalent principle proposed by Shelkunoff in 1936, namely, if all electromagnetic sources are inside a closed surface S, the fields distribution in the space outside the closed surface S can be obtained from the tangential electromagnetic fields on the surface S. The Plane Wave Spectrum method, also named the plane angular spectrum expansion method, is one of the pattern expansion methods. The basic idea is that, in a linear, uniform and isotropic medium without any source, the wave with a single frequency can be regarded as a composition of a series of plane waves in different directions. This method can be divided into the following basic steps (see Fig.1 for reference): Fig.1 3-D antenna-radome system The near-fields of the antenna incident upon the radome are calculated. In other words, find the fields at the inner surface 2 from the antenna at 2. The transmitted fields through the radome surface are calculated, i.e., find the field at the outer surface 2 from 2. The radome boresight contribution is calculated from the transmitted fields based on the tangential field distribution on the outer surface of the radome acted as a second source through the surface integration. In other words, the radiation in region 2 is determined from the fields at 2. 2, 2, 2 in Fig.1 are applied to calculate the backlobe contribution. The expression of the far-fields radiation pattern can be determined by pz R py R px R P E E E + + = . (1) where R R R R S x px S d ) z , y , x ( f E R = , R R R R S y py S d ) z , y , x ( f E R = R R R R S z pz S d ) z , y , x ( f E