Abstract:This research explores the influence of distinct tool-pin geometries on the mechanical and microstructural characteristics of single-pass friction stir-welded (SP-FSW) joints in 6 mm-thick Al-alloy (AA7075-T6) plates. The study involves three distinctive tool pin profiles: a cylindrical tool pin (M1), a square tool-pin (M2), and a conical tool-pin (M3), all featuring a scrolled shoulder, which was utilised to create the welded joints, ensuring that fully penetrated and defect-free welds were achieved by maintaining a constant tool rotation speed of 800 rev/min and a travel speed of 50 mm/min. Notably, the average grain size within the stir zone (SZ) of the M2 joint was smaller than the M1 and M3 joints. Furthermore, the microhardness of the M2 joint exhibited higher values in the thermo-mechanically affected zoneand SZ in contrast to the M1 and M3 welded joints. Additionally, the results of the tensile tests revealed joint efficiencies of 46.2%, 60.5%, and 51.1% for the M1, M2, and M3 joints, respectively. The ductility of M1, M2, and M3 welded joints was 8.68%, 11.3%, and 11.9%, respectively. The fractured tensile sample was characterised by SEM and micro-cracks and large dimples with brittle fractures were observed in all M1, M2, and M3 welded joints. Cette recherche explore l′influence de géométries distinctes des pointes d′outil sur les caractéristiques mécaniques et microstructurales des joints soudés par friction-malaxage à passe unique (SP-FSW) dans les tôles en alliage d′aluminium (AA7076-T6) de 6 mm d′épaisseur. L′étude implique trois profils distincts de pointes à outil: une pointe à outil cylindrique (M1), une pointe à outil carrée (M2) et une pointe à outil conique (M3), toutes dotées d′une épaule à enroulement, utilisées pour créer les joints soudés. Assurer des soudures à pénétration complète et sans défauts a été obtenu en maintenant une vitesse de rotation constante de l′outil de 800 tr/min et une vitesse de déplacement de 50 mm/min. Particulièrement, on a observé que la taille moyenne des grains dans la zone de brassage (SZ) du joint M2 était la plus petite comparée aux joints soudés M1 et M3. Par ailleurs, la microdureté du joint M2 exhibait des valeurs plus élevées dans la zone affectée thermo-mécaniquement (TMAZ) et SZ, en contraste avec les joints soudés M1 et M3. De plus, les résultats des essais de traction ont révélé des efficacités de 46.2%, 60.5% et 51.1% respectivement pour les joints M1, M2 et M3. En termes de % d′élongation, on a trouvé que la ductilité des joints soudés M1, M2 et M3 était respectivement de 8.68%, 11.3% et 11.9%. On a caractérisé l′échantillon de traction fracturé par microscopie électronique à balayage (MEB) et l′on a observé des microfissures et de grandes dépressions avec des ruptures fragiles dans tous les joints soudés de M1, M2 et M3.

Mechanical and microstructural characterisation on the effect of increasing tool rotational speed of friction stir welded AZ31-B magnesium alloy

Effect of rotation speed on microstructure and mechanical properties of bobbin tool friction stir welded AZ61 magnesium alloy

Effect of Tool Speed on Microstructure Evolution and Mechanical Properties of Friction Stir Welded Joints of Al-Mg-Si Alloy with High Cu Content

Effect of Low Welding and Rotational Speed on Microstructure and Mechanical Behaviour of Friction Stir Welded AZ31-AA6061-T6

Improving microstructural and mechanical properties of dissimilar friction stir welded AZ61/AZ40 joint

Microstructure evolution and high cycle fatigue failure behavior of friction stir-welded Ti–6Al–4V at varying welding speeds

Effect of tool traverse speed on microstructure and mechanical performance of friction stir welded 7020 aluminum alloy

Effect of welding speed on microstructure, nano-mechanical and nano-tribological characteristics of dissimilar friction stir welded AA6061-T6 and AZ31 alloy

Effect of rotation speed on microstructure and mechanical properties of refill friction stir spot welded 6061-T6 aluminum alloy

Microstructure and mechanical properties of friction-stir-welded high-Mg-alloyed Al–Mg alloy plates at different rotating rates

Influence of tool pin profiles on the mechanical and microstructural properties of a single-pass friction stir-welded AA7075-T6 aluminium alloy

Influence of Welding Speed on Microstructure and Mechanical Properties of 5251 Aluminum Alloy Joints Fabricated by Self-Reacting Friction Stir Welding

Effect of welding speed on microstructure and mechanical properties of Al−Mg−Mn−Zr−Tialloy sheet during friction stir welding

Tool rotational speed impact on temperature variations, mechanical properties and microstructure of friction stir welding of dissimilar high-strength aluminium alloys

Effect of rotation speed on microstructure and mechanical properties of bobbin tool friction stir welded T2 Copper

Effects of process parameters on microstructure and mechanical properties of friction stir lap linear welded 6061 aluminum alloy to NZ30K magnesium alloy

Assessing the Performance of a Dual-Speed Tool When Friction Stir Welding Cast Mg AZ91 with Wrought Al 6082

Evaluation of Microstructure, Mechanical Properties, Wear Resistance and Corrosion Behaviour of Friction Stir-Processed AZ31B-H24 Magnesium Alloy

Investigation of the microstructure, mechanical properties and fracture mechanisms of dissimilar friction stir welded aluminium/titanium joints

Simulation and Experimental Investigation of Friction Stir Welded Wrought Magnesium Alloy AZ31B

Influence of tool plunging rate on mechanical properties and microstructure of friction stir welded DMR249A high strength low alloy (HSLA) steel butt joints