Abstract:Sodium-sulfur (Na-S) batteries have been commercialized for stationary energy storage systems because of their low-cost fabrication and long-cycling stability. However, the Na-S batteries need to operate at high temperatures (> 300 o C) to maintain the molten state of sodium anode and sulfur cathode, which requires extra energy and raises safety issues when the solid electrolyte membrane fails. Therefore, low-temperature all-solid-state Na-S batteries (such as 60 o C) are highly desirable because of the improved safety and a lower operating temperature. To achieve high sulfur-specific capacity and long-cycling stability, the stable interfaces between electrodes and solid-state electrolyte are important for all-solid-state Na-S batteries. Herein, we demonstrate a strategy using Na alloy anodes to replace Na metal anode to solve the issues of unstable interface between Na metal and solid-state electrolytes. Na-Sn and Na-Sb alloys are first compared in terms of their alloying/dealloying process to identify the advantage of Na-Sb alloy as the anode. The Na-Sb alloy anode shows its superior stability against the solid electrolyte and undergoes a stable Na alloying/dealloying process at 0.04 mA cm -2 for over 500 hours. Sulfur-carbon composites with confined sulfur nanostructure were synthesized via the sulfur vapor deposition method and further utilized in full cells. Combining the optimized Na-Sb alloy anode and sulfur composite cathodes, the all-solid-state Na alloy-S battery shows improved rate performance and a high sulfur-specific capacity of 1377 mAh g -1 with good capacity retention of 70 % after 180 cycles at 60 o C (Figure 1a and b). Postmortem analysis of both the anode and cathode shows a reversible discharge/charge process after the first cycle and undergoes significantly rearranged distributions of carbon and solid electrolytes after 180 cycles due to severe volume change induced by repeated sodiation/desodiation process. These research results show a high sulfur specific capacity with long-cycling stability and shed light on further improving next-generation Na-S energy storage systems. Figure 1

High‐reversibility Sulfur Anode for Advanced Aqueous Battery

A Rechargeable Al/S Battery with an Ionic‐Liquid Electrolyte

Hybrid Electrolyte Design for High‐Performance Zinc–Sulfur Battery

Sulfamate-Derived Solid Electrolyte Interphase for Reversible Aqueous Zinc Battery

Sulfurized Composite Interphase Enables a Highly Reversible Zn Anode

Initiating a Reversible Aqueous Zn/Sulfur Battery through a “Liquid Film”

Highly Reversible Positive‐Valence Conversion of Sulfur Chemistry for High‐Voltage Zinc‐Sulfur Batteries

High-Valent Thiosulfate Redox Electrochemistry for Advanced Sulfur-Based Aqueous Batteries

High‐Capacity and Stable Sodium‐Sulfur Battery Enabled by Confined Electrocatalytic Polysulfides Full Conversion

Anodes for Rechargeable Lithium‐Sulfur Batteries

Al<sub>2</sub>S<sub>3</sub> Cathode for Rechargeable Aluminum-Sulfur Batteries with Improved Cycling Reversibility

Development of Stable All-Solid-State Sodium-Sulfur Batteries

Robust ZnS Interphase for Stable Zn Metal Anode of High-Performance Aqueous Secondary Batteries

An Efficient Li 2 S-based Lithium-ion Sulfur Battery Realized by a Bifunctional Electrolyte Additive

Highly Stable ZnS Anodes for Sodium-Ion Batteries Enabled by Structure and Electrolyte Engineering.

Robust Anode‐Free Sodium Batteries with Durably Sodophilic Interfaces by Suppressing Sodium‐Alloy Transformation

Rational design of zinc powder anode with high utilization and long cycle life for advanced aqueous Zn–S batteries

Quasi‐Solid Sulfur Conversion for Energetic All‐Solid‐State Na‐S Battery

Bidirectional Atomic Iron Catalysis of Sulfur Redox Conversion in High‐Energy Flexible ZnS Battery

A Universal Strategy Toward Low‐Cost Aqueous Sulfur–Iodine Batteries

Highly reversible zinc metal anode enabled by strong Brønsted acid and hydrophobic interfacial chemistry