Abstract:The limitation of poor mechanical stability and difficulties in printing electrically conductive components can be overcome owing to the recent introduction of nanotechnology into the field of additive manufacturing (AM) and the consequent development of nonconventional polymer nanocomposites suitable for 3D printing. In the present work, different weight percentages (up to 6 wt % in total) of carbon-based nanostructures-multiwalled carbon nanotubes (MWCNTs), graphene nanoplatelets (GNPs), and a combination of both fillers (MWCNTs/GNPs)-were incorporated into poly(lactic) acid (PLA, Ingeo™) in an attempt to overcome several limitations of conventional 3D manufacturing based on insulating materials. Solution blending and melt mixing were the two fabrication methods adopted for preparation of the samples under test. A comparison of the morphological, rheological, and electrical properties of the resulting nanocomposites was carried out. Moreover, for the same weight concentrations, the influence of physical and geometrical features (i.e., functionalization and aspect ratio) of the embedded fillers was also investigated. Rheological methods were applied to control the quality of fillers dispersion in PLA matrix. The rheological percolation threshold was considered as reference in order to evaluate the internal structure of nanodispersions. TEM visualization, combined with rheological characterizations, was used for efficient control of the nanofiller dispersion. DC characterization revealed that lower electrical percolation thresholds and higher values of electrical conductivity were achieved using fillers with a larger aspect ratio and melt mixing, respectively. Moreover, given the possibility of obtaining complex and appropriate shapes for electromagnetic compatibility (EC) applications, electromagnetic (EM) response of the nanocomposites at the highest filler concentration was investigated in GHz and THz regions. It was found that the electromagnetic shielding efficiency (EMI) of nanocomposites strongly depended on the aspect ratio of the nanofillers, whereas the type of processing technique did not have a significant effect. Therefore, a careful choice of methods and materials must be made to address the final application for which these materials and further 3D printed architectures are designed.

Engineering internal nanostructure in 3D‐printed materials via polymer molecular weight distribution

Development of Mechanically Enhanced Polycaprolactone Composites by a Functionalized Titanate Nanofiller for Melt Electrowriting in 3D Printing.

Nanostructure design of 3D printed materials through macromolecular architecture

Effect of Macromolecular Structure on Phase Separation Regime in 3D Printed Materials

Polymerization Induced Microphase Separation of ABC Triblock Copolymers for 3D Printing Nanostructured Materials

Driving macro-scale transformations in three-dimensional-printed biopolymers through controlled induction of molecular anisotropy at the nanoscale

Tuning the Mechanical Properties of 3D-printed Objects by Mixing Chain Transfer Agents in Radical Promoted Cationic RAFT Polymerization

Numerical Model of Jet Formation During Melt Electrowriting for Fabrication of Precise Structures

Tailoring Mechanical Properties of PμSL 3D-Printed Structures Via Size Effect

Morphological, Rheological and Electromagnetic Properties of Nanocarbon/Poly(lactic) Acid for 3D Printing: Solution Blending vs. Melt Mixing

Tailoring mechanical properties in 3D printed multimaterial architected structures

The effect of controlled intercalation on the mechanical performances and dimensional accuracy of material extrusion additive manufactured poly(lactic acid)/organo-montmorillonite nanocomposites

Effect of molecular weight on mechanical properties and microstructure of 3D printed poly(ether ether ketone)

Multimaterial 3D Printing for Arbitrary Distribution with Nanoscale Resolution

Essential Nanostructure Parameters to Govern Reinforcement and Functionality of Poly(lactic) Acid Nanocomposites with Graphene and Carbon Nanotubes for 3D Printing Application

Effects of printed bead volume on thermal history, polymer degree of crystallinity and mechanical properties in large scale additive manufacturing.

Precise modulation of molecular weight distribution for structural engineering

Size Effect in the Compression of 3D Polymerized Micro-Structures

Microphase Separation 3D Printing of Binary Inorganic Polymer Precursors to Prepare Nanostructured Carbon‐Ceramic Multimaterials

Enhancing the mechanical properties of biodegradable PLLA/PBAT blends for 3D filament via one-pot synthesized CNCs-PVAc powder

Tuning the Mechanical Properties of 3D-Printed Objects by Mixing Chain Transfer Agents in Norrish Type I Photoinitiated RAFT Polymerization