Abstract:Abstract This study develops a new numerical simulation model for rubble mound failure prediction caused by piping destruction under seepage flows. The piping has been pointed out as a significant cause of breakwater failure during tsunamis. Once boiling and heaving occur on the mound surface, the piping suddenly propagates in the opposite direction of seepage flow. For the seepage failure prediction, a coupled fluid-soil-structure simulator is developed by combining the ISPH for fluid and the DEM for rubble mounds and caisson blocks. The ISPH, a Lagrangian particle method for incompressible fluids, can simulate seepage and violent flows such as tsunamis. The DEM has been applied for discrete particle and rigid body simulations that include discontinuous deformation, as in the rubble mounds failure and large displacement of the caisson block. ISPH-DEM coupling simulations have already been proposed as a technique for multi-phase flows. Still, the technique cannot reproduce the sudden onset of piping from a stable mound. Two simple assumptions are applied to reduce the numerical cost for the fluid-soil-structure simulators of a breakwater structure composed of a rubble mound and the caisson block. Firstly, each rubble is modeled as an idealized spherical DEM particle with the mean diameter of the rubble. The ISPH particle size is assumed to be the same size as the DEM particle. Under these assumptions, the unresolved coupling model between rubble mound particles and fluid, which obtains the interaction through empirical drag force, should be applied. At the same time, the interaction between the fluid and the caisson block is fully resolved with the spatial resolution with the ISPH and DEM particle size. Our new contribution in this paper is how to model the interaction as an unresolved coupling between seepage flow simulated by ISPH and rubble mound particle modeled with DEM. Our original seepage failure experiment is simulated using the proposed ISPH-DEM coupling simulator. We identified the conventional drag force models as the unresolved coupling model are insufficient to initiate the boiling and piping observed in the experiment. It may be due in one part to excessive averaging of flow velocities caused by unresolved coupling. Therefore, Terzaghi’s critical hydraulic gradient is introduced to initiate the boiling and heaving. Unstable DEM particles, judged by Terzaghi’s critical hydraulic gradient, gradually lose their mass to represent unresolved suspended fine rubble mound particles. Our models qualitatively reproduce the sand boiling and backward erosion in the opposite direction of the seepage flow, as shown in the experiment.

Sand flow model based on the MPH-I method for reaching the static state

Incompressible Sph Scour Model for Movable Bed Dam Break Flows

MPM Modeling of Pile Installation in Sand: Contact Improvement and Quantitative Analysis

Depth-Averaged Two-Dimensional Model of Unsteady Flow and Sediment Transport Due to Noncohesive Embankment Break/Breaching

Numerical Investigation of Silted-Up Dam-Break Flow with Different Silted-Up Sediment Heights

Numerical Study of Violent Impact Flow Using a CIP-Based Model

Numerical Investigation on the Adaptation of Dam-Break Flow-Induced Bed Load Transport to the Capacity Regime over a Sloping Bed

Numerical simulation of submarine landslide tsunamis based on the smoothed particle hydrodynamics model

Micromechanics-based multimechanism bounding surface model for sands

Solid–liquid coupled material point method for simulation of ground collapse with fluidization

A well-balanced positivity preserving two-dimensional shallow flow model with wetting and drying fronts over irregular topography

SPH numerical simulation study on wind-sand flow structure of multi-diameter sand

A Two-Phase SPH Model for Massive Sediment Motion in Free Surface Flows

3D numerical simulation of debris-flow motion using SPH method incorporating non-Newtonian fluid behavior

A Fully Coupled Hydro-Mechanical Material Point Method for Saturated Dense Granular Materials

Development and experimental validation of a computational fluid dynamics-discrete element method sand production model

Simulation of Solid-Fluid Mixture Flow Using Moving Particle Methods

Experimental and Numerical Studies of Water–Sand Flow in Fractured Porous Media

HyPAM: A Hybrid Continuum-Particle Model for Incompressible Free-Surface Flows

Numerical experimental comparison of mudflow by smoothed particle hydrodynamics (SPH)

Seepage failure prediction of breakwater using an unresolved ISPH-DEM coupling method enriched with Terzaghi’s critical hydraulic gradient