Abstract:Inorganic CsPbIBr2 perovskite has been considered as a promising light-absorbing material for solar cells due to its high stability and suitable bandgap. Although the remarkable improvement of CsPbIBr2 PSC has been achieved, the efficiency of this cell is still lower than those of other analogues and far below its theoretical limit. This is mainly due to the serious charge recombination in the as-fabricated CsPbIBr2 cells derived from the poor-quality CsPbIBr2 perovskite film with a large quantity of defects and numerous grain boundaries. Therefore, fabricating high-quality CsPbIBr2 perovskite film is a key factor for the further efficiency improvement of CsPbIBr2 PSCs. Herein, phenylthiourea (PTU) additive is introduced into the CsPbIBr2 precursor to tailor the crystallization of CsPbIBr2 perovskite for fabricating high-quality CsPbIBr2 perovskite. The C=S group of PTU can coordinate with PbBr2 in the precursor owing to the lone-pair electrons on S and the empty orbits of Pb2+. The strong interaction between PTU and the CsPbIBr2 precursor components can form PTU·Pb···Br(I) intermediate phase in the precursor upon PTU introduction. The PTU·Pb···Br(I) intermediate phase can reduce the nucleation rate of perovskite and modulate the perovskite crystal growth because the extra energy is required to break the strong coordination bond in the intermediate phase, resulting in a low crystallization rate of CsPbIBr2 perovskite. Such a retardation of perovskite crystallization is conducive to the formation of high-crystallinity perovskite film with smooth surface, large crystal grains, high crystallization, and low density of defect. Meanwhile, the decomposition of PTU during thermal annealing makes the S2– inserted into interstitial of CsPbIBr2 crystal lattice, which greatly enhance the stability of CsPbIBr2 perovskite. The carbon-based PSCs with a normal n-i-p structure of FTO/compact-TiO2 layer/meso-TiO2 layer/perovskite film/carbon layer are fabricated, and their photovoltaic performances are measured under a simulated AM1.5 illumination (100 mW·cm–2). The PSC based on PTU-CsPbIBr2 perovskite delivers a high power conversion efficiency of 10.09%, which is much higher than that of the control device. This great improvement of photovoltaic performance can be attributed to the largely promoted perovskite quality, which enhances the charge collection and suppresses the charge recombination in the device. In addition, the unencapsulated device preserves 82% of the initial efficiency after being stored under ambient condition for 35 days, suggesting excellent stability. Therefore, this work provides an effective complementary strategy for effectively improving the performance of inorganic PSCs.

Crystallization Control to Prepare Uniform CsPbI 2 Br Thin Films for High-Efficiency Perovskite Solar Cells

Crystallization Management of CsPbI2Br Perovskites by PbAc2-incorporated Twice Spin-Coating Process for Efficient and Stable CsPbI2Br Perovskite Solar Cells

In Situ Observation and Control of Crystallization Dynamics for Stable and Efficient CsPbI3-Based 2D Perovskite Solar Cells

Antisolvent‐Free Heterogenous Nucleation Enabled by Employing 4‐Tert‐Butyl Pyridine Additive and Two‐Step Annealing for Efficient CsPbI2Br Perovskite Solar Cells

Manipulating the Crystallization and Phase Transition for High-Performance CsPbI<sub>2</sub>Br Solar Cells

Photovoltaic Performance Improvement of All‐Inorganic CsPbBr3 Perovskite Solar Cells by Antisolvent Assisted Crystallization

Ambient Air Temperature Assisted Crystallization for Inorganic CsPbI2Br Perovskite Solar Cells

Modulation of Nucleation and Crystallization in PbI2 Films Promoting Preferential Perovskite Orientation Growth for Efficient Solar Cells

Ultra-smooth CsPbI2Br Film Via Programmable Crystallization Process for High-Efficiency Inorganic Perovskite Solar Cells

High crystallinity and photovoltaic performance of CsPbI3 film enabled by secondary dimension

CaF 2 Nanoparticle-Induced γ-CsPbI 2.81 Br 0.19 Heterogeneous Crystallization for High-Efficiency Flexible All-Inorganic Perovskite Solar Cells

Recent Advances in CsPbX3 Perovskite Solar Cells: Focus on Crystallization Characteristics and Controlling Strategies

Crystallinity Control and Strain Release in Wide-Bandgap Perovskite Film via Seed-Induced Growth for Efficient Photovoltaics

Controlling the Intermediate Phase to Improve the Crystallinity and Orientation of Cs3Sb2ClxI9‐x Films for Efficient Solar Cells

Ionic Liquid Surface Treatment-Induced Crystal Growth of CsPbIBr2 Perovskite for High-Performance Solar Cells

MACl-Induced Controlled Crystallization in Sequentially Deposited Perovskites for High-Efficiency and Stable Perovskite Solar Cells

Crystallization Regulation and Lead Leakage Prevention Simultaneously for High-Performance CsPbI 2 Br Perovskite Solar Cells

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

Facile Hydrogen‐Bonding Assisted Crystallization Modulation for Large‐area High‐quality CsPbI2Br Films and Efficient Solar Cells

CaF2 Nanoparticle-Induced Γ-Cspbi2.81br0.19 Heterogeneous Crystallization for High-Efficiency Flexible All-Inorganic Perovskite Solar Cells.

CsPb2Br5 assisted direct crystallization of 3D perovskite phase for highly efficient and stable solar cells