Film cooling performance evaluation of the furcate hole with cross-flow coolant injection: A comparative study

Cun-liang Liu,Lin Ye,Fan Zhang,Rong Huang,Bingran Li

DOI: https://doi.org/10.1016/j.ijheatmasstransfer.2020.120457

IF: 5.2

2021-01-01

International Journal of Heat and Mass Transfer

Abstract:<p>Turbine blades are consistently exposed to high-temperature gas in an effort to increase the maximum efficiency of gas turbine engines. Therefore, a growing need exists to protect the outer surfaces from high-temperature gas. Film cooling has long been used as an active thermal protection scheme, and the shaped film-hole is one possible solution to the aforementioned problem. Based on the actual coolant supply channel of the turbine blades, the film cooling performance of a novel furcate hole fed by cross-flow coolant injection with 135-deg ribs was experimentally investigated in this study. The Reynolds numbers of the main-flow and cross-flow are 10,000 and 100,000, respectively, and the blowing ratio M ranges from 0.5 to 2.0. The adiabatic film effectiveness η and heat transfer coefficient of the furcate hole are obtained by the transient liquid-crystal measurement technique, and a detailed comparison between the furcate hole and cylindrical hole geometries, simple and compound hole, is presented. The results show that the span-wise width of the film coverage is significantly more comprehensive than that of the compound hole due to the configuration of the span-wise expansion for the furcate hole. At a lower M, the film coverage gradually narrows, and the η gradually decreases along the flow direction for the furcate hole. The heat transfer enhancement of the furcate hole is the highest among the studied cases, and the heat transfer uniformity is much impoverished. With an increasing M, the advantages of the high η of the furcate hole are gradually revealed. The degree of deflection of the film coverage gradually increases toward the +Y side. Both the effectiveness and magnitude of the span-wise η are improved at M=1.0. At a larger M of 2.0, the heat transfer enhancement is the weakest, and the heat transfer uniformity is improved. The net heat-flux reduction is introduced to comprehensively evaluate the cooling performance. The values of the traditional holes invariably decrease as M increases, whereas that of the furcate hole first increases and then decreases. As M increases to 1.0 and 2.0, the comprehensive benefits of the furcate hole become more apparent.</p>

engineering, mechanical,thermodynamics,mechanics

What problem does this paper attempt to address?

The main problem that this paper attempts to solve is to evaluate how the film - cooling performance of a new - type furcate hole is under the conditions of cross - flow coolant injection and 135 - degree inclined ribs. Specifically, the research objectives include:

1. **Influence of Expansion Angles on Film - Cooling Performance**: Explore how the two expansion angles affect the film - cooling performance of the furcate hole. Existing research mainly focuses on fan - shaped holes and backward - inclined holes. The expansion at the outlet of these holes can increase the jet width and intensify the jet deflection, but the expansion in the flow direction can suppress the decline of the film - cooling effect. Therefore, what kind of film - cooling characteristics will be produced when these two expansion angles are applied to the furcate hole?

2. **Influence of the Channel with Inclined Ribs on Film - Cooling Performance**: Research how the internal cross - flow with inclined ribs affects the film - cooling performance of the furcate hole. Actual blades usually adopt a combination of internal cooling channels and external film - cooling, but most research only focuses on internal or external cooling and ignores their interaction. Therefore, the research on this comprehensive cooling method has broad prospects.

3. **Influence of Blowing Ratio on Film - Cooling Performance**: Explore the influence of the blowing ratio (M) on the film - cooling performance under the condition of ribbed cross - flow. Changes in the blowing ratio will affect the distribution of the coolant and the cooling effect, so it is necessary to analyze in detail the film - cooling performance at different blowing ratios.

Through experiments and numerical simulations, the researchers aim to comprehensively evaluate the film - cooling performance of this new - type furcate hole and compare it with traditional holes (such as simple holes and compound holes), in order to provide new ideas and methods for the efficient cooling design of turbine blades.