Abstract:The bond properties at layer interfaces are a required input in mechanistic asphalt pavement models. For design and analysis procedures, involving the calculation of key responses that are commonly linked to performance, perfect bond conditions are regularly assumed between layers. One emerging approach for prolonging the service life of asphalt pavements, either new or rehabilitated, is installing asphalt grid reinforcement (AGR) products between paving lifts. In these cases, the perfect bond assumption may not hold – undermining the reinforcement potential. Accordingly, the objective of this study was to investigate the effects of layer interface properties on key responses in pavements with AGR. The investigation was carried out by combining results from a full-scale construction, laboratory tests on asphalt concrete (AC) cores, and synthetic simulations. The latter were performed with a recently developed semi-analytic mechanistic code that can accept AGR products. This code can handle time- and temperature-dependent layer and interface properties, as well as moving loads. From the laboratory tests, it was found that the bond between AC lifts, with and without an AGR, is time- and temperature-dependent – best characterised by a relaxation interface stiffness function. This relaxation function was measured to be consistently larger without an AGR than with an AGR. Nonetheless, pavement simulations showed that including an AGR has no pronounced effect on strain magnitudes under high-speed/low-temperature conditions, can lessen horizontal strain magnitudes at the reinforced interface and at the AC bottom (mainly under slow-speed/high-temperature conditions, and depending on the installation depth of the AGR), and has no pronounced effect on deflections regardless of the loading speed and temperature level. It is concluded that even if laboratory measurements display a reduced interface stiffness when including an AGR, the reduction may not have any practical implication on key pavement responses, and the reinforcement potential is not necessarily undermined. The modelling and experimental approaches outlined and utilised in this study offer a rational tool for analysing this matter/question on a case-by-case basis.

Influence of bonding condition of different interfaces on the mechanical responses and failure mode of asphalt pavement

Multiscale Modelling of Bitumen-Aggregate Interfaces from Molecular Debonding to Pull-off Strength

Test Method to Evaluate the Effect of Interface Bond Conditions on Top-Down and Reflective Cracking

Study On Dynamic Response Characteristics Of Saturated Asphalt Pavement Under Multi-Field Coupling

Influence of bonding conditions on flexible base asphalt pavement under non-uniform vertical loads

Structural Mechanics Analysis of Asphalt Pavement Using Large Stone Asphalt Mixture As Base

Characterizing Bitumen-Aggregate Interfacial Failures under Coupled Size Effects of Bitumen Film Thickness and Aggregate Surface Roughness

Relation of homogeneity and mechanical response of asphalt pavements

Reflective crack initiation of asphalt overlays on jointed concrete pavement using finite element model

Effect of Bond Condition on Flexible Pavement Performance

Numerical Analysis for Basalt Fiber Reinforced High-Viscosity Asphalt Concrete Bridge Deck Pavement

Fatigue performance of interface bonding between asphalt pavement layers using four-point shear test set-up

Investigation of Fracture Failure and Water Damage Behavior of Asphalt Mixtures and Their Correlation with Asphalt-Aggregate Bonding Performance

Asphalt Layer Cracking Behavior and Thickness Control of Continuously Reinforced Concrete and Asphalt Concrete Composite Pavement

Finite Element Analysis and Laboratory Testing for Design of Asphalt Concrete Pavement on Concrete Bridges

Modulus Prediction of Asphalt Concrete with Imperfect Bonding Between Aggregate–asphalt Mastic

Cracking Propagation of Asphalt Pavement of Stabilized Base with Inorganic Binder under Coupling of Overloaded Traffic and Temperature

Multiscale Finite Element Analysis of Layer Interface Effects on Cracking in Semi-Flexible Pavements at different temperatures

Mechanistic investigation of grid-reinforced asphalt pavements with measured interface properties

Temperature Changes of Interlaminar Bonding Layer in Different Seasons and Effects on Mechanical Properties of Asphalt Pavement

Analysis of Interlayer Crack Propagation and Strength Prediction of Steel Bridge Deck Asphalt Pavement Based on Extended Finite Element Method and Cohesive Zone Model (XFEM–CZM) Coupling