Abstract:The crystal model of NaCl-type FCC-TiC (1− x ) N x was established, and the crystal structure of nonstoichiometric TiC (1− x ) N x was optimized by first-principles calculation method. The binding energy, formation energy, elastic modulus, density of states (DOS) and charge density of TiC (1− x ) N x were calculated. The crystal structure, electronic structure and mechanical properties of TiC (1− x ) N x were studied. The effects of bonding types and bonding properties on the mechanical properties were analyzed. The results show that the optimized TiC (1− x ) N x crystal structure, with the increase in N content, lattice constant and cell volume decrease, TiN crystal structure is easy to form, and its thermodynamics is the most stable. The analysis of B/G, B/C44, Cauchy pressure and Poisson's ratio shows that TiC has the highest brittleness, and TiN has the best toughness, while TiC (1− x ) N x is between TiC and TiN. The covalent bonds are mainly Ti-C and Ti-N bonds, but there are also a certain number of C-N bonds, Ti-C and Ti-N ionic bonds, and Ti-Ti metallic bonds. The doping of N changes the interaction force between the electrons in the metallic d layer and the non-metallic 2p orbital electrons, and also changes the interaction force between the electrons in the metallic bond d layer, thus affecting the hardness and toughness of TiC (1− x ) N x . As C atoms are gradually replaced by C atoms in the TiC (1− x ) N x crystal structure, the density of states at EF gradually increases, which leads to the enhancement of the metal bond Ti d –Ti d , thereby improving the conductivity of the material. The transition from Ti–C bond to Ti–N bond leads to the decrease in covalent bond, the enhancement of ionic property, the increase in hardness and the decrease in toughness. The nonstoichiometric TiC (1− x ) N x powders were synthesized by carbothermal reduction technique, and the lattice constants obtained by XRD were basically consistent with the calculated values. XPS analysis shows that there are Ti–C, Ti–N, C–C and C–N bonds in TiC (1− x ) N x . The experimental results are in good agreement with the calculated electronic structure and bond type, which indicates the reliability of the crystal model and calculation method.

Phase stability and elastic properties in the $Al_{1-x-y}Cr_{x}Ti_{y}N$ system from first principles

Phase Stability and Elasticity of TiAlN

A First-Principles Study of Mechanical and Electronic Properties of Cr0.5-xAl0.5TMxN Hard Coatings (TM = Ti, V, Y, Zr, Hf, and Ta)

Ab initio study of the alloying effect of transition metals on structure, stability and ductility of CrN

First-principles study of elastic properties of Cr-Al-N

Einfluss von Sc, Y, Ti, Zr, Hf, V, Nb und Ta auf strukturelle und mechanische Eigenschaften von Cr-Al-N-Schichten

Exploration of the microstructure space in TiAlZrN ultra-hard nanostructured coatings

Structure, mechanical properties and thermal stability of CrAlNbN/TiN multilayers

First-principles calculations to investigate phase stability, elastic and thermodynamic properties of TiMoNbX (X=Cr, Ta, Cr and Ta) refractory high entropy alloys

Sputter deposited chromium nitride based ternary compounds for hard coatings

Experimental study and thermodynamic modeling of the Al-Co-Cr-Ni system

Phase stability, chemical bonding and mechanical properties of titanium nitrides: a first-principles study

First-principles thermodynamic investigation on the α phases in TiO and TiNb binary system

First-Principles Study on the Mechanical Properties and Electronic Structure of Nonstoichiometric TiC(1−x)Nx

Phase Composition, Hardness, and Thermal Shock Properties of AlCrTiN Hard Films with High Aluminum Content

The Effect of Nb Doping on the Properties of Ti-Al Intermetallic Compounds Using First-Principles Calculations

Improvement of Tribological Performance of TiAlNbN Hard Coatings by Adding AlCrN

Microstructure, Mechanical Properties, Wear and Erosion Performance of a Novel High Entropy Nitride (AlCrTiMoV)N Coating Produced by Cathodic Arc Evaporation

Modification mechanism of Ti-6Al-4V alloy with pre-coated Ti-Cu-Al multilayer film treated by ion nitriding: Experiments and first-principles calculations

FCC-to-HCP Phase Transformation in CoCrNix Medium-Entropy Alloys

Mechanical, Tribological, and Corrosion Resistance Properties of (TiAlxCrNbY)Ny High-Entropy Coatings Synthesized Through Hybrid Reactive Magnetron Sputtering