Abstract:Image-based personalized Finite Element Models (pFEM) could detect alterations in physiological deformation of human vertebral bodies, but their accuracy has been seldom reported. Meaningful validation experiments should allow vertebral endplate deformability and ensure well-controlled boundary conditions. This study aimed to (i) validate a new loading system to apply a homogeneous pressure on the vertebral endplate during vertebral body compression regardless of endplate deformation; (ii) perform a pilot study on human vertebral bodies measuring surface displacements and strains with Digital Image Correlation (DIC); (iii) determine the accuracy of pFEM of the vertebral bodies. Homogeneous pressure application was achieved by pressurizing a fluid silicone encased in a rubber silicone film acting on the cranial endplate. The loading system was validated by comparing DIC-measured longitudinal strains and lower-end contact pressures, measured on three homogeneous pseudovertebrae of constant transversal section at 2.0 kN, against theoretically calculated values. Longitudinal strains and contact pressures were rather homogeneous, and their mean values close to theoretical calculations (5% underestimation). DIC measurements of surface longitudinal and circumferential displacements and strains were obtained on three human vertebral bodies at 2.0 kN. Complete displacement and strain maps were achieved for anterolateral aspects with random errors ≤0.2 μm and ≤30 μstrain, respectively. Venous plexus and double curvatures limited the completeness and accuracy of DIC data in posterior aspects. pFEM of vertebral bodies, including cortical bone mapping, were built from computed tomography images. In anterolateral aspects, pFEM accuracy of the three vertebrae was: (i) comparable to literature in terms of longitudinal displacements (R2>0.8); (ii) extended to circumferential displacements (pooled data: R2>0.9) and longitudinal strains (zero median error, 95% error: <27%). Circumferential strains were overestimated (median error: 39%). The new methods presented may permit to study how physiological and pathologic conditions influence the ability of vertebral endplates/bodies to sustain loads.

Numerical model of pressure generated by elastic compression garments on a compressible human limb analogue

Bone Geometry on the Contact Stress in the Shoulder for Evaluation of Pressure Ulcers: Finite Element Modeling and Experimental Validation.

Biomechanical response of varicose veins to elastic compression: a numerical study

Three-dimensional dynamic homogenous modeling: The biomechanical influences of leg tissue stiffness on pressure performance of compression biomedical therapeutic textiles

Stiffness in compression therapy: Analytical estimation of pressure changes beneath textile compression devices

Characterizing the biomechanical transmission effects of elastic compression stockings on lower limb tissues by using 3D finite element modelling

Finite element simulation of knee joint pressure and surface displacement: relationship and influencing factors

Modelling indentation of human lower-limb soft tissue: simulation parameters and their effects

In vivo mechanical response of thigh soft tissues under compression: A two-layer model allows an improved representation of the local tissue kinematics

Etude mécanique des articles de contention et de leurs effets sur la jambe humaine. Mechanical investigation of compression stockings and of their effects on the human leg

Combining Freehand Ultrasound-Based Indentation and Inverse Finite Element Modeling for the Identification of Hyperelastic Material Properties of Thigh Soft Tissues

Pressure Responses of Tourniquet Practice Models to Calibrated Force Applications

Numerical analysis of the strain distribution in skin domes formed upon the application of hypobaric pressure

Identification of excessive contact pressures under hand orthosis based on finite element analysis

Pipette Aspiration of Hyperelastic Compliant Materials: Theoretical Analysis, Simulations and Experiments

Proposal of Method for Estimating Clothing Pressure of Tight-Fitting Garment Made from Highly Elastic Materials: Hybrid Method Using Apparel CAD and Finite Element Analysis Software

Study on clothing pressure distribution of calf based on finite element method

Finite element analysis to model ischemia experienced in the development of device related pressure ulcers

A novel optimization approach for bio-design of therapeutic compression stockings with pressure fit

Applying a homogeneous pressure distribution to the upper vertebral endplate: Validation of a new loading system, pilot application to human vertebral bodies, and finite element predictions of DIC measured displacements and strains

Finite-element simulation of functional knee sleeves based on three-dimensional modeling of the knee joint