Abstract:With the premise of investigating mechanical properties, the thermal conductivity of autoclaved aerated concrete (AAC) is a key index of self-insulation block walls for building energy conservation. This study focused on the effect of pore structures on the mechanical performance and thermal conductivity of AAC with the comparison of AAC base materials. Different kinds of AAC and their base materials were prepared and experimentally investigated. While maintaining a consistent mix proportion of the AAC base material, the pore structure of AAC was changed by the dosage of aluminum power/paste, foam stabilizer, and varying the stirring time of aluminum paste. The steam curing systems of AAC and the base material were determined based on SEM (Scanning Electronic Microscopy) and XRD (X-ray Diffraction) tests. With almost the same apparent density, the pore size decreased with the increasing content of foam stabilizer, and the mixing time of aluminum paste and foam stabilizer has a great influence on pore size. The thermal conductivity test and compressive test results indicated that that pore size had an effect on the thermal conductivity, but it had little effect on the compressive strength, and the thermal conductivity of sand aeration AAC was 8.3% higher than that of fly ash aeration AAC; the compressive strength was 10.4% higher, too. With almost the same apparent density, the regression mathematical model indicates that the thermal conductivity of AAC increased gradually with the increase of pore size, but it had little effect on the compressive strength. From the test results of basic mechanical properties, the mechanical model of cubic compressive strength, elastic modulus, axial compressive strength, and splitting tensile strength was obtained. The proposed stress–strain relationship model could well describe the relationship of AAC and the base material at the rising section of the curve.

Potential usage of porous autoclaved aerated concrete waste as eco-friendly internal curing agent for shrinkage compensation

Carbonation Curing of Industrial Solid Waste‐based Aerated Concretes

Effects of Red Mud on Workability and Mechanical Properties of Autoclaved Aerated Concrete (AAC)

Properties and Internal Curing of Concrete Containing Recycled Autoclaved Aerated Lightweight Concrete as Aggregate

Effect of Nano CaCO3 on the Properties of Autoclaved Aerated Concrete

Mitigating Autogenous Shrinkage of Alkali-Activated Slag Mortar by Using Porous Fine Aggregates as Internal Curing Agents

Preparation of Autoclaved Aerated Concrete from Construction Waste

Utilization of Red Mud with High Radiation for Preparation of Autoclaved Aerated Concrete (AAC): Performances and Microstructural Analysis

Waste Originating from the Cleaning of Flue Gases from the Combustion of Industrial Wastes as a Lime Partial Replacement in Autoclaved Aerated Concrete

Internal Curing Efficiency of Prewetted LWFAs on Concrete Humidity and Autogenous Shrinkage Development

Integrated Shrinkage, Relative Humidity, Strength Development, and Cracking Potential of Internally Cured Concrete Exposed to Different Drying Conditions

Internal Curing Utilising Recycled Concrete Aggregate: A Sustainable Approach for Improving High-Strength Concrete's Performance

Utilization of Solid Waste in the Production of Autoclaved Aerated Concrete and Their Effects on its Physio-mechanical and Microstructural Properties: Alternative Sources, Characterization, and Performance Insights

Leaching assessment of aerated concrete made of recycled shale gas drilling cuttings: Particular pollutants, physical performance and environmental characterization

Durability and shrinkage performance of self-compacting concrete containing recycled fine clay brick aggregate

Effect of Pore Structure on Thermal Conductivity and Mechanical Properties of Autoclaved Aerated Concrete

Experimental Study on the Interrelationship between the Moisture Content and Drying Shrinkage of Autoclaved Aerated Concrete Wallboard

The use of ceramics as an internal curing agent in high performance concrete with variable temperature curing to improve mechanical characteristics

Wet-milling disposal of autoclaved aerated concrete demolition waste – A comparison with classical supplementary cementitious materials

Research on the methods for improving the compressive strength of solid waste-based high-strength autoclaved aerated concrete

Performance of Autoclaved Aerated Concrete (AAC) Containing Recycled Ceramic and Gypsum Waste as Partial Replacement for Sand