Abstract:The emerging photovoltaic technology, namely perovskite photovoltaics, follows a style to the blooming flower with superficial prosperity described by the ancient poet Yuxi Liu. Metal-halide perovskite has become one of the most promising photovoltaic materials for thin-film solar-cell applications, mainly due to its exellent visible light capture capability, large diffusion coefficients and long diffusion lengths of charge carriers (both electrons and holes). The reported power conversion efficiency of laboratory produced perovskite solar cells (PSCs) has exceeded 25%. However, this value was only achieved for devices of less than 0.1 cm(2)dimensions, and decreases significantly with the increase in area (for example, down to 11.6% for a device area of similar to 800 cm(2), showing the issues with the scalability). In PSCs, the electron transport layer (ETL) has to perform two essential functions, which are related: (i) to collect and transfer charges after the injection of electrons from the perovskite light harvester; and (ii) to block the backflow of holes, thus realizing effective charge separation and suppressing charge carrier recombination. However, there are several critical issues associated with the ETLs which limit the further development of the PSCs. For example, the experimentally obtained open-circuit voltages in PSCs are typically much lower compared to the theoretical voltage limit with their optical bandgaps between 1.59 and 1.63 eV. This is mainly attributed to inefficient charge transport in the PSCs due to inhomogeneous charge accumulation and serious interfacial recombination at the interfaces between the ETL and the perovskite active layer. We scan recent developments of ETLs in PSCs, and discuss design methodologies, mechanisms, processing and characterization of new types of ETLs. High power conversion efficiency with large open-circuit voltages/photo-currents could be achieved through designing materials and microstructures for high-quality ETLs with a high electron mobility, high electrical conductivity and pinhole-free film morphology. It is crucial to balance the charge diffusion processes in the respective charge collective layers of PSCs as the interfaces between the ETLs and perovskites along with their interfacial structures play key roles in achieving new solid-state mesoscopic solar cells optimized open circuit voltages and output photocurrents.

High‐Efficiency and Durable Inverted Perovskite Solar Cells with Thermally‐Induced Phase‐Change Electron Extraction Layer

Solution Processed Inorganic V2Ox As Interfacial Function Materials for Inverted Planar-Heterojunction Perovskite Solar Cells with Enhanced Efficiency

Polyethyleneimine High-Energy Hydrophilic Surface Interfacial Treatment Toward Efficient and Stable Perovskite Solar Cells

Efficient Inverted Perovskite Photovoltaics Through Surface State Manipulation

In situ Blending For Co‐Deposition of Electron Transport and Perovskite Layers Enables Over 24% Efficiency Stable Inverted Solar Cells

Thermal Management Enables More Efficient and Stable Perovskite Solar Cells

Bridging the Interfacial Contact for Improved Stability and Efficiency of Inverted Perovskite Solar Cells

Efficient and stable perovskite solar cells fabrication in open air through adopting a dye interlayer

Interfacial Passivation of the p-Doped Hole-Transporting Layer Using General Insulating Polymers for High-Performance Inverted Perovskite Solar Cells

Enhanced Efficiency and Stability for the Inverted High‐Bandgap Perovskite Solar Cell via Bottom Passivation Strategy

Laser Derived Electron Transport Layers with Embedded p‐n Heterointerfaces Enabling Planar Perovskite Solar Cells with Efficiency over 25%

Efficient Planar Perovskite Solar Cells with Low-Temperature Atomic Layer Deposited TiO2 Electron Transport Layer and Interfacial Modifier

Low Temperature Combustion Synthesized Indium Oxide Electron Transport Layer for High Performance and Stable Perovskite Solar Cells

Efficient Gradient Potential Top Electron Transport Structures Achieved by Combining an Oxide Family for Inverted Perovskite Solar Cells with High Efficiency and Stability

A low-temperature TiO2/SnO2 electron transport layer for high-performance planar perovskite solar cells

Thermally stable inverted perovskite solar cells using an electropolymerized Zn-porphyrin film as a dopant-free hole-transporting layer

[6,6]-Phenyl-C 61 -Butyric Acid Methyl Ester/Cerium Oxide Bilayer Structure as Efficient and Stable Electron Transport Layer for Inverted Perovskite Solar Cells.

High-Efficiency Perovskite Solar Cells with Improved Interfacial Charge Extraction by Bridging Molecules

Ethyl Thioglycolate Assisted Multifunctional Surface Modulation for Efficient and Stable Inverted Perovskite Solar Cells

Advances in design engineering and merits of electron transporting layers in perovskite solar cells

Simultaneously Enhanced J(Sc) And Ff By Employing Two Solution-Processed Interfacial Layers For Inverted Planar Perovskite Solar Cells