Abstract:Depending on the application, establishing a strategy for selecting the type of powder bed fusion technology—from electron beam (EB-PBF) or laser powder bed fusion (L-PBF)—is important. In this study, we focused on the β-type Ti–15Mo–5Zr–3Al alloy (expected for hard-tissue implant applications) as a model material, and we examined the variations in the microstructure, crystallographic texture, and resultant mechanical properties of specimens fabricated by L-PBF and EB-PBF. Because the melting mode transforms from the conduction mode to the keyhole mode with an increase in the energy density in L-PBF, the relative density of the L-PBF-built specimen decreases at higher energy densities, unlike that of the EB-PBF-built specimen. Although both EB-PBF and L-PBF can obtain cubic crystallographic textures via bidirectional scanning with a 90° rotation in each layer, the formation mechanisms of the textures were found to be different. The <100> texture in the build direction is mainly derived from the vertically grown columnar cells in EB-PBF, whereas it is derived from the vertically and horizontally grown columnar cells in L-PBF. Consequently, different textures were developed via bidirectional scanning without rotation in each layer: the <110> and <100> aligned textures along the build direction in L-PBF and EB-PBF, respectively. The L-PBF-built specimen exhibited considerably better ductility, but slightly lower strength than the EB-PBF-built specimen, under the conditions of the same crystallographic texture and relative density. We attributed this to the variation in the microstructures of the specimens; the formation of the α-phase was completely absent in the L-PBF-built specimen. The results demonstrate the importance of properly selecting the two technologies according to the material and its application.

Manufacturing of a nanosized TiB strengthened Ti-based alloy via electron beam powder bed fusion

Enhanced strength and ductility of nano-TiBw-reinforced titanium matrix composites fabricated by electron beam powder bed fusion using Ti6Al4V–TiBw composite powder

Electron Beam Welding and Post Heat Treatment of a New Near-Beta High-Strength Ti-4Al-5Mo-5V-5Cr-1Nb Alloy

Microstructure evolution of Ti64-TiBw composites via electron beam powder bed fusion using as-prepared composite powder as feedstock

Microstructure and mechanical properties of B modified Ti-Fe alloy manufactured by casting, forging and laser melting deposition

Engineering fine grains, dislocations and precipitates for enhancing the strength of TiB 2 -modified CoCrFeMnNi high-entropy alloy using Laser Powder Bed Fusion

Material Characterisation and Computational Thermal Modelling of Electron Beam Powder Bed Fusion Additive Manufacturing of Ti2448 Titanium Alloy

Microstructures Of Components Synthesized Via Electron Beam Selective Melting Using Blended Pre-Alloyed Powders Of Ti6al4v And Ti45al7nb

Microstructural evolution and mechanical properties of eutectoid Ti–7Ni alloy produced by electron beam powder bed fusion

Microstructure and Mechanical Properties of Large Ti6Al4V Components by Electron Beam Powder Bed Fusion

Nanoparticle-mediated ultra grain refinement and reinforcement in additively manufactured titanium alloys

Effects of in Situ TiB2 on the Microstructural Evolution, Mechanical Properties, and Friction Behavior of the Al-Si-Cu Alloys Processed by Laser Powder-Bed Fusion

A systematic approach to optimize parameters in manufacturing complex lattice structures of NiTi using electron beam PBF process

Enhancement of Grain Refinement and Heat Resistance in TiB2-reinforced Al-Cu-Mg-Fe-Ni Matrix Composite Additive Manufactured by Electron Beam Melting

Overcoming the Strength-Ductility Trade-off and Anisotropy of Mechanical Properties of Ti6Al4V with Electron Beam Powder Bed Fusion

Engineering Fine Grains, Dislocations and Precipitates for Enhancing the Strength of TiB2-modified CoCrFeMnNi High-Entropy Alloy Using Laser Powder Bed Fusion

Comparison of Microstructure and Mechanical Behavior of Ti-35Nb Manufactured by Laser Powder Bed Fusion from Elemental Powder Mixture and Prealloyed Powder

Comparison of microstructure, crystallographic texture, and mechanical properties in Ti–15Mo–5Zr–3Al alloys fabricated via electron and laser beam powder bed fusion technologies

The Dispersion-Strengthening Effect of TiN Nanoparticles Evoked by Ex Situ Nitridation of Gas-Atomized, NiCu-Based Alloy 400 in Fluidized Bed Reactor for Laser Powder Bed Fusion

Microstructure, Mechanical Properties and Strengthening Mechanism of Tib2 Nanoparticles-Reinforced Cocrfemnni High-Entropy Alloy

Electron beam powder bed fusion of Ti-30Ta high-temperature shape memory alloy: microstructure and phase transformation behaviour