Abstract:Ortho‐, meta‐, and para‐isomers of fluorophenylethylammonium iodine (F‐PEAI) are tested in constructing perovskite quantum wells (PQWs) for 3D perovskites. Among them, p‐F‐PEAI offers optimal charge distribution and minimal steric hindrance, enhancing PbI2 interaction, as confirmed by TEM and GIWAXS. This results in improved surface passivation and charge transport. Inverted PSCs achieve a boosted PCE to 25.03% with enhanced stability. The photovoltaic performance of inverted perovskite solar cells (PSCs) is often hindered by trap‐induced non‐radiative recombination and photochemical degradation occurring at the upper interfaces and the grain boundaries of perovskite films. Herein, ortho‐, meta‐, and para‐isomers of fluorophenylethylammonium iodine (F‐PEAI) organic spacer molecules are evaluated for the construction of perovskite quantum wells (2D or quasi‐2D, PQWs) to encapsulate 3D perovskites. Among the three variants, p‐F‐PEAI leads to the most symmetric charge distribution and the weakest steric hindrance which resulting in reinforced interactions with PbI2 and perovskite, the enhanced out‐of‐plane orientation is confirmed by Grazing incidence wide‐angle X‐ray scattering (GIWAXS) results. Density functional theory and crystal orbital Hamilton population (COHP) calculations further confirm that p‐F‐PEAI engages most strongly with the perovskite structure. Moreover, transmission electron microscopy (TEM) characterization is used to illustrate that p‐F‐PEAI‐assisted 2D PQWs effectively passivate both the grain boundaries and surfaces of perovskites. This configuration facilitates effective surface passivation, improves charge carrier transport, and significantly suppresses non‐radiative recombination. The resultant inverted PSCs achieve an excellent power conversion efficiency (PCE) of 25.03% with a fill factor (FF) of 85.11%. The unencapsulated devices exhibit enhanced long‐term stability under ambient environments and continuous light illumination.

In-Situ Dipole Formation to Achieve High Open-Circuit Voltage in Inverted Perovskite Solar Cells via Fluorinated Pseudohalide Engineering

Inhibiting Interfacial Nonradiative Recombination in Inverted Perovskite Solar Cells with a Multifunctional Molecule

Interfacial Passivation of the p-Doped Hole-Transporting Layer Using General Insulating Polymers for High-Performance Inverted Perovskite Solar Cells

Efficient Inverted Perovskite Solar Cells with Low Voltage Loss Achieved by a Pyridine‐Based Dopant‐Free Polymer Semiconductor

Judicious Fluorination of Perovskite Quantum Wells Enables Over 25% Efficiency in Inverted Solar Cells

Efficient Inverted Perovskite Photovoltaics Through Surface State Manipulation

Reduced bilateral recombination by functional molecular interface engineering for efficient inverted perovskite solar cells

Inverted Perovskite Solar Cells with >85% Fill Factor via Sequential Interfacial Engineering

Towards 26% efficiency in inverted perovskite solar cells via interfacial flipped band bending and suppressed deep-level traps

Proton‐transfer‐induced in Situ Defect Passivation for Highly Efficient Wide‐bandgap Inverted Perovskite Solar Cells

High-Performance Perovskite Solar Cells with Low Open-Circuit Voltage Loss and Excellent Stability after p-F-PEAI Posttreatment

Enhancing the Open-Circuit Voltage of Perovskite Solar Cells by up to 120 mV using π-Extended Phosphoniumfluorene Electrolytes as Hole Blocking Layers

In situ energetics modulation enables high-efficiency and stable inverted perovskite solar cells

Minimizing Interfacial Energy Losses Via Fluorination Strategy Toward High-Performance Air-Fabricated Perovskite Solar Cells

Minimizing the Buried Interfacial Energy Loss by a Fluorine-Substituted Small Molecule for 25.92%-Efficiency and Stable Inverted Perovskite Solar Cells

Efficient Inverted Perovskite Solar Cells with a Low‐Dimensional Halide/Perovskite Heterostructure

Synchronous Elimination of Excess Photoinstable PbI2 and Interfacial Band Mismatch for Efficient and Stable Perovskite Solar Cells

Reduced Open‐Circuit Voltage Loss of Perovskite Solar Cells Via Forming P/p+ Homojunction and Interface Electric Field on the Surfaces of Perovskite Film

Tailoring Interfacial Dipole Molecules to Mitigate Carrier and Energy Losses in Perovskite Solar Cells

Surface Polarity Regulation by Relieving Fermi‐Level Pinning with Naphthalocyanine Tetraimides toward Efficient Perovskite Solar Cells with Improved Photostability

Interface Dipole Induced Field‐Effect Passivation for Achieving 21.7% Efficiency and Stable Perovskite Solar Cells