Abstract:Carbon nanotube/continuous carbon fiber reinforced poly(ethylene terephthalate) (CNT/CCF/PET) composites are prepared by melt impregnating. The effects of CF and CNT content on the mechanical properties, melt and crystallization behaviors, and submicroscopic morphology of CNT/CCF/PET composites are studied. The tensile test results show that the increase of CF and the addition of appropriate amount of CNT improved the tensile strength and tensile modulus of the composites. When the content of CNT is 1.0 wt% and the content of CF is 56 wt%, the properties of the composites are the best, with tensile strength of 1728.7 MPa and tensile modulus of 25.1 GPa, which is much higher than that of traditional resin matrix composites. The results of dynamic mechanical analysis (DMA) show that the storage modulus of the composites increased with the increase of CF and CNT content. In particular, the addition of CNT greatly reduced the loss modulus of the composites. Morphological analysis show that the addition of CNT improved the fiber–matrix interface of the composite, which changes from fiber pull-out and fracture failure to fiber matrix fracture failure, and the fiber matrix interface is firmly bonded. In addition, there are polymer coated CNT protrusions on the surface of the fiber was observed. The results of differential scanning calorimetry (DSC) show that the melting temperature and crystallization temperature of the composites increased with the increase of CF content. The addition of CNT had little effect on the melting temperature of the composites, but it further improved the crystallization temperature of the composites. The effect of CNT content on the crystallization kinetics of the composites is studied. The non-isothermal crystallization kinetics of the composites is described by Jeziorny's improved Avrami equation. The results show that CNT has a great influence on the crystallization type of the composites. As a nucleating agent, CNT has obvious heterogeneous nucleation effect in the composites, which improves the crystallization rate of PET.

Non-isothermal crystallization kinetics and activation energy modeling of carbon nanotubes dispersed high-density polyethylene and polypropylene blends

Influence of Nanofiller Dimensionality on the Crystallization Behavior of HDPE/carbon Nanocomposites

Sliding Behaviour of Carbon Nanothread Within a Bundle Embedded in Polymer Matrix

Effects of MXene on Nonisothermal Crystallization Kinetics of Isotactic Polypropylene.

PE/PE‐g‐MAH/Org‐MMT Nanocomposites. II. Nonisothermal Crystallization Kinetics

More Dominant Shear Flow Effect Assisted by Added Carbon Nanotubes on Crystallization Kinetics of Isotactic Polypropylene in Nanocomposites

Molecular Dynamics Simulation on the Crystallization Behavior of Cyclic Polyethylene Affected by Functionalized Carbon Nanotubes

Nonisothermal Crystallization Kinetics of Ethylene-Butene Copolymer/Low-Density Polyethylene Blends

Carbon Nanotube Migration in a Compatibilized Blend System, Leading to Kinetically Induced Enhancement in Electrical Conductivity and Mechanical Properties

Role of multi-wall carbon nanotube network in composites to crystallization of isotactic polypropylene matrix

Effect of Carbon Nanotubes on the Mechanical Properties and Crystallization Behavior of Poly(ether Ether Ketone)

Influence of Reduced Graphene Oxide on the Rheological Response and Chain Orientation on Shear Deformation of High Density Polyethylene

Concurrent effect of shear flow and CNT presence on crystallization behavior and electrical properties of polypropylene based nanocomposites: A comprehensive structure-property investigation

Mechanical Properties, Melting and Crystallization Behaviors, and Morphology of Carbon Nanotubes/Continuous Carbon Fiber Reinforced Polyethylene Terephthalate Composites

Effects of Carbon Nanofibers on Crystalline Structures and Properties of Ultrahigh Molecular Weight Polyethylene Blend Fabricated Using Twin‐screw Extrusion

Effective Enhancement of a Carbon Nanothread on the Mechanical Properties of the Polyethylene Nanocomposite

Conductivity Insights Into the Carbon Nanotubes Mobility Restricted by the Long‐Branched Chains During the Thermal Annealing, Fast Shear Flow and Melt to Solid Cooling Process

Carbon nanotubes in blends of polycaprolactone/thermoplastic starch

Effect of Carbon Nanotube on the Melt Modification of LDPE with Glycidyl Methacrylate: Efficiency of Grafting Reaction and Rheological Property

Mechanical and Thermal Properties Modeling, Sorption Characteristics of Multiscale (Multiwalled Carbon Nanotubes/Glass Fiber) Filler Reinforced Polypropylene Composites

Fabrication and characterization of microwave cured high-density polyethylene/carbon nanotube and polypropylene/carbon nanotube composites