Abstract:Titanium is a widely used metal in biomedical applications due to its low toxicity, but its mechanical properties need to be tailored for different applications. Efforts are called for to search for effective and yet non-toxic elements to be alloyed with Ti to improve its strength. Fitting in this category, Mn and Mo are two such alloying elements. In this study, Ti-6Mn-4Mo alloy was manufactured by laser-directed energy deposition (DED) through in situ alloying of Ti, Mn, and Mo elemental powders. This study was intended to not only demonstrate for the first time the printability of the Ti-Mn-Mo ternary system by laser DED but also investigate the basic mechanical properties and corrosion resistance of the obtained alloy. Under the as-built condition, the alloy consisted mainly of ß phase, while after heat treatment it was transformed into α phase. The average ultimate tensile strength under as-built condition was 706.0 MPa, lower than similar alloys from conventional methods. However, the average hardness reached 421.1 HV for the as-built condition, much higher than the similar alloys made through conventional methods. On the other hand, the corrosion resistance of the obtained alloy was found to be relatively low compared to similar alloys produced with traditional methods. In addition, heat treatment was not able to significantly change the tensile properties or the corrosion resistance. In essence, the exploratory study indicates that the DED-produced Ti-Mn-Mo alloy could be deposited without cracks and major voids, and shows that its high hardness and modulus are attractive to applications for high wear resistance. However, further investigation is needed to improve strength, ductility, and corrosion resistance of the alloy.

Synergistic interactions between wear and corrosion of Ti-16Mo orthopedic alloy

The effect of Cu content on corrosion, wear and tribocorrosion resistance of Ti-Mo-Cu alloy for load-bearing bone implants

Enhancing Passivation Behaviors and Wear Resistance of Biomedical Ti-15Mo Alloy via {332} Twinning Pre-Tension and Aging

Tribocorrosion Behavior of TC18 Titanium Alloy: A Discussion about the Interaction Between Galvanic Corrosion and Wear

Impact of scandium on mechanical properties, corrosion behavior, friction and wear performance, and cytotoxicity of a β-type Ti–24Nb–38Zr–2Mo alloy for orthopedic applications

Computational design of corrosion-resistant and wear-resistant titanium alloys for orthopedic implants

Corrosion and wear behavior of Ti-5Cu-xNb biomedical alloy in simulated body fluid for dental implant applications

Effect of surface oxidation on wear and tribocorrosion behavior of forged and selective laser melting-based TC4 alloys

Tribological Behavior of Direct Metal Laser Sintering–Manufactured Ti6Al4V Alloy in Different Biofluids for Orthopedic Implants

Electrochemical and wear properties of biomedical Ti–Nb–Ag alloy

Multi-material Ti6Al4V & PEEK cellular structures produced by Selective Laser Melting and Hot Pressing: A tribocorrosion study targeting orthopedic applications

Tribological behavior and in vitro biocompatibility of powder metallurgical Ti–15Mo/HA composite for bone repair

Corrosion and Wear Performance of Β-Ti Based Biomedical Shape Memory Alloys

Corrosion Behaviour and Biocompatibility Evaluation of Low Modulus Ti–16Nb Shape Memory Alloy As Potential Biomaterial

Tribocorrosion Behavior of NiTi Biomedical Alloy Processed by an Additive Manufacturing Laser Beam Directed Energy Deposition Technique

Surface nano-architectures and their effects on the mechanical properties and corrosion behavior of Ti-based orthopedic implants

Corrosion fatigue behavior of porous Cu-bearing Ti alloy fabricated by selective laser melting

Mechanical, corrosion, and wear properties of biomedical Ti–Zr–Nb–Ta–Mo high entropy alloys

Corrosion and Tribocorrosion Behaviors of AISI 316 Stainless Steel and Ti6Al4V Alloys in Artificial Seawater

Effect of Heat Treatment on Microstructure, Mechanical and Corrosion Behavior of Ti-7Mo-8Nb Alloy for Biomedical Applications

An exploratory study on biocompatible Ti-6Mn-4Mo alloy manufactured by directed energy deposition