Abstract:Laser-textured surfaces enabling reversible wettability switching and improved optical properties are gaining importance in cutting-edge applications, including self-cleaning interfaces, tunable optical lenses, microfluidics, and lab-on-chip systems. Fabrication of such surfaces by combining nanosecond-laser texturing and low-temperature annealing of titanium Ti-6Al-4V alloy was demonstrated by Lian et al. in ACS Appl. Mater. Inter. 2020, 12 (5), 6573-6580. However, it is difficult to agree with (i) their contradictory explanation of the wettability transition due to low-temperature annealing and (ii) their theoretical description of the optical behavior of the laser-textured titanium surface. This comment provides an alternative view-supported by both experimental results and theoretical investigation-on how the results by Lian et al. could be interpreted more correctly. The annealing experiments clarify that controlled contamination is crucial in obtaining consistent surface wettability alterations after low-temperature annealing. Annealing of laser-textured titanium at 100 °C in contaminated and contaminant-free furnaces leads to completely different wettability transitions. Analysis of the surface chemistry by XPS and ToF-SIMS reveals that (usually overlooked) contamination with hydrophobic polydimethylsiloxane (PDMS) may arise from the silicone components of the furnace. In this case, a homogeneous thin PDMS film over the entire surface results in water repellency (contact angle of 161° and roll-off angle of 15°). In contrast, annealing under the same conditions but in a contaminant-free furnace preserves the initial superhydrophilicity, whereas the annealing at 350 °C turns the hydrophobicity "off". The theoretical calculations of optical properties demonstrate that the laser-induced oxide layer formed during the laser texturing significantly influences the surface optical behavior. Consequently, the interference of light reflected by the air-oxide and the oxide-metal interfaces should not be neglected and enables several advanced approaches to exploit such optical properties.

Influence of Surface Roughness on Phosphonation and Wettability of Nanosecond Laser‐Treated Titanium Surfaces

Investigations in the fabrication of surface patterns for wettability modification on a Zr-based bulk metallic glass by nanosecond laser surface texturing

Study on the Fabrication of Titanium Surface Texture by Nanosecond Laser and Its Wettability

Modification of wettability property of titanium by laser texturing

Superhydrophobic Surface Preparation and Wettability Transition of Titanium Alloy with Micro/Nano Hierarchical Texture

Femtosecond laser modification of titanium surfaces: direct imprinting of hydroxylapatite nanopowder and wettability tuning via surface microstructuring

Influence of Surface Treatments Developed for Oral Implants on the Physical and Biological Properties of Titanium. (I) Surface Characterization.

Influence of Er:YAG laser irradiation on surface properties of Ti-6Al-4V machined and hydroxyapatite coated

Wettability Behaviour of Metal Surfaces after Sequential Nanosecond and Picosecond Laser Texturing

Influence of laser fluences and scan speeds on the morphologies and wetting properties of titanium alloy

Controllable hydrophilic titanium surface with micro-protrusion or micro-groove processed by femtosecond laser direct writing

Laser Texturing for Superwetting Titanium Alloy and Investigation of Its Erosion Resistance

Comment on "Bioinspired Reversible Switch between Underwater Superoleophobicity/Superaerophobicity and Oleophilicity/Aerophilicity and Improved Antireflective Property on the Nanosecond Laser-Ablated Superhydrophobic Titanium Surfaces"

Enhancement of Hydrophilicity of Nano-Pitted TiO2 Surface Using Phosphoric Acid Etching

Study on surface properties of nanosecond laser textured plasma nitrided titanium alloy

Biological Performance of Titanium Surfaces with Different Hydrophilic and Nanotopographical Features

Study on the Wettability and Abrasion Resistance of Ultrafast-Laser-Textured Ti Surface

Influence of Instantaneous and Delayed Overlaps on Surface Topography and Wettability of a Femtosecond Laser Textured Surface

Superhydrophobic Surface of Ti6Al4V using Direct Nanosecond Laser Texturing

Surface Modification of Ti3Al2.5V Titanium Alloy Using Laser Texturing With Improved Wettability, Corrosion and Bioactivity Behaviour

Influence of femtosecond laser pulse sequence on the morphology and roughness of titanium surface micro-patterns