Abstract:Bioartificial blends of poly-(epsilon-caprolactone) (PCL) with a polysaccharide (starch, S; dextran, D; or gellan, G) (PCL/S, PCL/D, PCL/G 90.9/9.1 wt ratio) were prepared by a solution-precipitation technique and widely characterized by differential scanning calorimetry analysis (DSC), Fourier transform infrared-attenuated total reflectance spectroscopy (FTIR-ATR), optical microscopy (OM), wide-angle X-ray diffraction analysis (WAXD), and thermogravimetry (TGA). DSC showed that the polysaccharide reduced the crystallinity of PCL and had a nucleation effect, which was also confirmed by OM analysis. Hoffman-Weeks analysis was performed on PCL and blend samples allowing calculation of their equilibrium melting temperatures (). WAXD showed that the crystalline unit cell type was the same for PCL and blends. FTIR-ATR did not evidence interactions between blend components. Thermal stability was affected by the type of polysaccharide. Microparticles (<125 microm) were produced from blends by cryogenical milling and characterized by scanning electron microscopy analysis (SEM). Selective laser sintering (SLS), a new rapid prototyping technology for scaffold fabrication, was applied to sinter blend microparticles according to a PC-designed two-dimensional geometry (strips and 2 x 2 mm(2) square-meshed grids). The optimal experimental conditions for sintering were established and laser beam parameters (beam speed, BS, and power, P) were found for each blend composition. Morphology of sintered objects was analyzed by SEM and found to be dependent on the morphology of the sintered powders. Sintered samples were analyzed by chemical imaging (CI), FTIR-ATR, DSC, and contact angle analysis. No evidence of the occurrence of degradation phenomena was found by FTIR-ATR for sintered samples, whereas DSC parameters of PCL and blends showed changes which could be attributed to some molecular weight decrease of PCL during sintering. CI of sintered samples showed that the polysaccharide phase was homogeneously dispersed within the PCL matrix, with the only exception being the PCL/D blend. The contact angle analysis showed that all samples were hydrophilic. Fibroblasts were then seeded on scaffolds to evaluate the rate and the extent of cell adhesion and the effect of the polysaccharides (S, D, G) on the bioactivity of the PCL-based blends.

Tailored binary polymer system PCL-PEO for advanced biomedical applications: Optimization, characterization and in vitro analysis

A Novel Approach for Tailored Medicines: Direct Writing of Janus Fibers

Development of Random and Ordered Composite Fiber Hybrid Technologies for Controlled Release Functions

Fabrication of Patterned Polymer-Antibiotic Composite Fibers Via Electrohydrodynamic (ehd) Printing

Electrospun Ibuprofen-Loaded Blend PCL/PEO Fibers for Topical Drug Delivery Applications

Tuning the properties of polycaprolactone-based fibers by using polyethylene oxide / polycaprolactone block copolymers

Modulating Drug Release from Short Poly(ethylene Glycol) Block Initiated Poly(L-lactide) Di-block Copolymers

Synthesis, Characterisation and Phase Transition Behaviour of Temperature-Responsive Physically Crosslinked Poly (N-Vinylcaprolactam) Based Polymers for Biomedical Applications.

A strategy to tailor the mechanical and degradation properties of PCL-PEG-PCL based copolymers for biomedical application

Preparation, Characterization And In Vitro Release Properties Of Ibuprofen-Loaded Microspheres Based On Polylactide, Poly(Epsilon-Caprolactone) And Their Copolymers

Preparation, characterization and in vitro release properties of ibuprofen-loaded microspheres based on polylactide, poly(ε-caprolactone) and their copolymers

A review of preparation methods and biomedical applications of poly(ε-caprolactone)-based novel formulations

New PCL/PEC Blends: In Vitro Cell Response of Preosteoblasts and Human Mesenchymal Stem Cells

Biocompatibility studies and characterization of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate)/polycaprolactone blends.

Synthesis composit electrospun based gum-resin/polycaprolactone fibers for biomedical application

Enzymatic Biodegradation Of Poly(Ethylene Oxide-B-Epsilon-Caprolactone) Diblock Copolymer And Its Potential Biomedical Applications

Biocompatibility studies and characterization of poly(3-hydroxybutyrate-<i>co</i>-3-hydroxyhexanoate)/polycaprolactone blends

Functional copolymer coatings on electrospun fibers via photo‐initiated chemical vapor deposition

Cellulose nanocrystals/polyethylene glycol as bifunctional reinforcing/compatibilizing agents in poly(lactic acid) nanofibers for controlling long-term in vitro drug release

Synthesis of Functional Polycaprolactones Via Passerini Multicomponent Polymerization of 6-Oxohexanoic Acid and Isocyanides

Blends of Poly-(ε-caprolactone) and Polysaccharides in Tissue Engineering Applications