Exploration of low heat rejection engine characteristics powered with carbon nanotubes-added waste plastic pyrolysis oil
Parthasarathy Murugesan,P.V. Elumalai,Dhinesh Balasubramanian,S. Padmanabhan,N. Murugunachippan,Asif Afzal,Prabhakar Sharma,K. Kiran,JS Femilda Josephin,Edwin Geo Varuvel,Thanh Tuan Le,Thanh Hai Truong
DOI: https://doi.org/10.1016/j.psep.2023.06.051
2023-07-07
Process Safety and Environmental Protection: Transactions of the Institution of Chemical Engineers, Part B
Abstract:Compression ignition (CI)-powered alternative energy sources are currently the main focus due to the constantly rising worldwide demand for energy and the growing industrialization of the automotive sector . Due to their difficulty of disposal, non-degradable plastics contribute significantly to solid waste and pollution. The waste plastics were simply dropped into the sea, wasting no energy in the process. Attempts have been made to convert plastic waste into usable energy through recycling. Waste plastic oil (WPO) is produced by pyrolyzing waste plastic to produce a fuel that is comparable to diesel . Initially, a standard CI engine was utilized for testing with diesel and WPO20 (20% WPO+80% diesel). When compared to conventional fuel, the brake thermal efficiency (BTE) of WPO20 dropped by 3.2%, although smoke, carbon monoxide (CO), and hydrocarbon (HC) emissions were reasonably reduced. As a result, nitrogen oxide (NOx) emissions decreased while HC and CO emissions marginally increased in subsequent studies utilizing WPO20 with the addition of 5% water. When combined with WPO20 emulsion, nanoadditives have the potential to significantly cut HC and CO emissions without impacting performance. The possibility of incorporating nanoparticles into fuel to improve performance and lower NOx emissions should also be explored. In order to reduce heat loss through the coolant, prevent heat transfer into the cylinder liner, and increase combustion efficiency , the thermal barrier coating (TBC) material is also coated inside the combustion chamber surface. In this work, low heat rejection (LHR) engines powered by emulsion WPO20 containing varying percentages of carbon nanotubes (CNT) are explored. The LHR engine was operated with a combination of 10 ppm, 20 ppm, and 30 ppm CNT mixed with WPO20. It was shown that while using 20 ppm of CNT with WPO20, smoke, hydrocarbons, and carbon monoxide emissions were reduced by 11.9%, 21.8%, and 22.7%, respectively, when compared to diesel operating in normal mode. The LHR engine achieved the greatest BTE of 31.7% as a result of the improved emulsification and vaporization induced by CNT-doped WPO20. According to the study's findings, WPO20 with 20 ppm CNT is the most promising low-polluting fuel for CI engines. The present study dealt with the combined effect of Groundnut shell (GS)-originated nanoparticles and biodiesel derived from Pithecellobium Dulce seed on the performance and emission characteristics of a diesel engine. For the fuel-preparation step, GS nanoparticles were pulverized using ball milling, while Pithecellobium Dulce biodiesel was synthesized by using a transesterification process with the support of a Ni-doped ZnO catalyst prepared by the co-precipitation method, resulting in a 5 % higher yield in comparison with using a conventional KOH catalyst. Moreover, both GS and as-prepared biodiesel were characterized through Scanning Electron Microscope, Fourier Transform Infrared Spectroscopy, Differential Scanning Calorimetry, and Thermogravimetric analysis. Relating to the experimental analysis of the engine characteristics, the obtained results disclosed an increase in brake thermal efficiency and a decrease in brake-specific fuel consumption by adding 100 ppm of GS (G100) nanoparticles to the B20 (20 % Pithecellobium Dulce biodiesel/80 % diesel fuel) compared to B20. More importantly, emissions of HC, CO, and smoke decreased for B20 compared to diesel fuel but a further reduction of the above-mentioned emissions was observed for B20/G100. In contrast, CO 2 and NO x emissions increased with B20 and B20/G100 in comparison with diesel fuel. Also, the addition of Groundnut shell nanoparticles with biodiesel enhanced the combustion characteristics such as in-cylinder pressure and heat release rate. Indeed, the order of peak in-cylinder pressure and heat release rate was found to be B20/G100 > B20 > diesel fuel, which can be attributed to reasons such as fuel accumulation, ignition delay, and heating value. Finally, this present study showed a viable approach to replace conventional diesel fuel with biodiesel combined with bio-nanoparticles in an eco-friendly manner and sustainability. Further, the present approach could be suitably applied to diesel engines without any modifications. There is a need to find alternative fuels to replace the fossil fuels and also to reduce the harmful emissions. Biomass based fuels are one such alternate fuel to diesel. The main aim of this study is to find the suitability of sweet almond oil ( Prunus amygdalus dulcis oil) in compression ignition engine (CI), moreover to enchance the performance and emission param -Abstract Truncated-
English Else