Abstract:Abstract The extent of crosslinking a polymeric fracturing gel can significantly contribute to the success or failure of a hydraulic fracturing treatment. In certain cases, excessive crosslinking while the fluid is in the tubulars can result in friction pressures that are too high, and may prohibit the treatment from achieving the design goals. With titanium (Ti) or zirconium (Zr) crosslinked gels, which are known to be prone to irreversible shear degradation, early crosslinking in the tubulars can substantially reduce the final gel strength, even to the degree that near wellbore proppant transport is compromised, and the treatment may screenout. On the other hand, a Ti or Zr crosslinked gel which crosslinks substantially after exiting the perforations may not have sufficient proppant transport capability to complete the treatment successfully. Varying treatment conditions such as mixwater composition and temperature, tubular shear rate and transit time, and reservoir temperature pose difficult challenges to routinely achieving the optimal crosslinking state. Conditions such as offshore wellbore temperature profiles and viscous heating in smaller diameter tubing can further complicate the task. Various chemical means have been employed to tune the crosslinking temperature for specific treating conditions. These methods involve addition of chemicals to control the crosslinking kinetics, such as pH buffers, crosslinker concentration, and competing ligands to temporarily bind the metal crosslinker. Blended crosslinkers containing a single Group 4 (Ti, Zr) metal with different organic ligands with different binding strengths have been employed to achieve crosslinking at two temperature ranges so that early viscosity for proppant transport can be developed. Mixed metal crosslinkers, such as aluminum and Zr have also been formulated for this same purpose. This paper examines the disadvantages of these strategies, and describes the development and deployment of a high-temperature fracturing fluid system that has shown to overcome those issues. Introduction Achieving the design fluid viscosity at in-situ conditions is critical for a number of reasons. Fracture initiation, propagation, and resulting dimensions are strongly influenced by the viscosity. Proppant transport, also determined by fluid properties, is necessary for fracture areal coverage and helps determine well performance. Overcoming the various demands on a gel formed from a single organometallic crosslinker are difficult to achieve (Fig. 1). Ideally, the crosslinking could be triggered instantaneously just after the fluid exits the perforations, avoiding high friction pressure and degradation resulting from shear in the tubulars and perforations. Crosslink the fluid too early and the friction in the tubulars will rise significantly and, as it will be shown later, a significantly crosslinked fluid cannot be sheared without permanent damage to the polymer molecular weight, and therefore to the fluid viscosity. Low initial viscosity from crosslinking too late may result in a narrow, near-wellbore fracture, impeding proppant transport. Either crosslinking a single organometallic system too early or too late risks premature screenout. (Nolte 1988, Walser 1988, Almond 1984) Gelling at varying temperatures can be achieved by delivering a crosslinker that has two (or more) organometallic complexes: one that could yield limited crosslinking at a lower temperature for initial proppant transport, and the second complex for higher temperatures experienced in the fracture. This approach would manage friction pressures. However, the gel would still suffer irreversible degradation due to the strong metal bonds existing during high shear in the tubulars.

Synthesis and performance evaluation of crosslinker for seawater‐based fracturing fluid

Preparation and Antifiltration Performance of Organic Zirconium Crosslinker for Guar Gum‐Fracturing Fluid

Preparation and laboratory study of a sodium carboxymethyl cellulose smart temperature‐controlled crosslinked gel fracturing fluid system

Effect of Chemical Composition of Metal–Organic Crosslinker on the Properties of Fracturing Fluid in High-Temperature Reservoir

Preparation and rheological properties of organic zirconium crosslinked KGM/HPAM gel

Rheological Performance of High-Temperature-Resistant, Salt-Resistant Fracturing Fluid Gel Based on Organic-Zirconium-Crosslinked HPAM

Ultra-deep reservoirs gel fracturing fluid with stepwise reinforcement network from supramolecular force to chemical crosslinking

Dynamic cross-linking mechanism of acid gel fracturing fluid

Quantitative characterization of the crosslinking degree of hydroxypropyl guar gum fracturing fluid by low-field NMR

Experimental Investigation and Performance Evaluation of a Novel High Temperature Tolerant Seawater-based Fracturing Fluid

Study of Fracturing Fluid on Gel Breaking Performance and Damage to fracture conductivity

Development and Gelation Mechanism of Ultra-High-Temperature-Resistant Polymer Gel

Supramolecular polymer-based gel fracturing fluid with a double network applied in ultra-deep hydraulic fracturing

A New Shear-Tolerant High-Temperature Fracturing Fluid

Synthesis and evaluation of salt tolerant delayed-crosslinking fracturing fluid system in ultra-deep high temperature wells

Preparation and Performance Evaluation of a Self-Crosslinking Emulsion-Type Fracturing Fluid for Quasi-Dry CO2 Fracturing

Experimental investigation on the high-pressure sand suspension and adsorption capacity of guar gum fracturing fluid in low-permeability shale reservoirs: factor analysis and mechanism disclosure

Novel Mussel‐Inspired High‐Temperature Resistant Gel with Delayed Crosslinking Property for Ultra‐Deep Reservoir Fracturing

Modified guanidine gel fracturing fluid system and performance optimization for ultra-deep and ultra-high temperature oil and gas reservoirs

Doubly cross‐linked polymer gels with ultra‐high‐thermal stability for hydrofracking

Synthesis and evaluation of water-soluble fracturing fluid thickener based on hydrophobic association