Abstract:In the era of Industry 4.0, researchers in various fields have paid special attention to digital twin technology, which can realize real-time mapping between virtual and physical space. In this paper, a new general framework for response prediction of composite structures based on digital twins is proposed. The tensile testing process of standard samples of carbon fiber-reinforced composites (CFRCs) is used as the twinning object. Moreover, the development of a digital twin and composite structural response prediction based on the generic framework is demonstrated. First, standard CFRC tensile samples are prepared, and relevant raw data are acquired. Subsequently, the microscopic parameters of the standard CFRC tensile samples are obtained by scanning electron microscopy. Geometric measurements are performed to determine the macroscopic parameters, which, together with the material properties of carbon fibers and matrix, are used as the input parameters of a multi-scale virtual physical model (MVPM). The MVPM is used to simulate the actual tensile process using the multi-scale finite element method (FEM). Then, the real-time measurement data from the physical space are transferred to the virtual space through sensors. At the same time, the computationally time-consuming MVPM is downscaled to meet the real-time requirements for the online deployment of the digital twins. In this paper, the backpropagation (BP) neural network model is used to train the input and output parameter data of the MVPM to obtain a reduced-order model (ROM). In addition, to improve the prediction accuracy of the structural response of the digital twin, three model update strategies (MUS) of the ROM are proposed: 1) MUS 1 is based on the ROM, adding the tested sample historical data for the training model update strategy; 2) MUS 2 is based on the ROM 1, adding the measured real-time data of the current sample for training and updating to obtain the ROM 2; 3) MUS 3 is based on the predicted structural response data of ROM 2. Combined with the real-time measured data of the current sample, a higher-order fitting real-time correction is performed to obtain ROM 3. Finally, the tensile process of five CFRC standard samples is demonstrated based on the structural response prediction of the digital twin. The strain response prediction and contour visualization of the whole sample is achieved with limited strain gauge data. By comparison, MUS 2 has higher prediction accuracy than MUS 1 after adding the real-time measured data of the current sample. The prediction errors of MUS 1 and MUS 2 at the later stages of the stretching process are within 10%, with the minimum error of MUS 1 being 15.73% and that of MUS 2 being 3.36%. With the correction of high-order fitting, MUS 3 can achieve a stable prediction error of 20% or less in future moments, and the error can be reduced to less than 5%, reaching a minimum error of 0.44% at the critical tail section near tensile failure.

A low‐cost trans‐scale model for the collaborative analysis of the manufacturing and in‐service process of unidirectional CFRP composites

Machine Learning and Materials Informatics Approaches for Predicting Transverse Mechanical Properties of Unidirectional CFRP Composites with Microvoids

Multiscale Collaborative Optimization for the Thermochemical and Thermomechanical Cure Process During Composite Manufacture

An integrated modeling of the curing process and transverse tensile damage of unidirectional CFRP composites

Multiscale Model of Micro Curing Residual Stress Evolution in Carbon Fiber-Reinforced Thermoset Polymer Composites

Evolution of Curing Residual Stresses in Composite Using Multi-Scale Method

An integrated computational materials engineering framework to analyze the failure behaviors of carbon fiber reinforced polymer composites for lightweight vehicle applications

Concurrent n-scale modeling for non-orthogonal woven composite

Optimization of Process-Induced Residual Stresses in Automated Manufacturing of Thermoset Composites

Multi-scale Numerical Calculations for the Interphase Mechanical Properties of Carbon Fiber Reinforced Thermoplastic Composites

Multiscale analysis method and experiments for the transverse mechanical property of unidirectional fiber-reinforced composites

Collaborative multi‐scale optimization of molding processes for thermosetting/quartz fiber composites based on balancing between efficiencies and mechanical properties

Application of Scalable Sensor-Assisted Multi-Scale Computational Methods in the Simulation of Micro Mechanical Behavior of Composite Materials

Experimental study on the mechanical property of carbon fiber reinforced polymer with the combined application of digital twin and reduced order algorithm

Enhancing the Forming Accuracy of CFRP through a Global Compensation Method by Introducing an Optimal Profile

A Numerical Bayesian-calibrated Characterization Method for Multiscale Prepreg Preforming Simulations with Tension-Shear Coupling

An approach to predict the mechanical properties of CFRP based on cross-scale simulation

Microscale viscoplastic analysis of unidirectional CFRP composites under the influence of curing process

A Coupled FEM-FFT Concurrent Multiscale Method for the Deformation Simulation of CFRPs Laminate

Micromechanical modeling for longitudinal tensile property of unidirectional CFRP considering dispersion of fiber properties

A New General Framework for Response Prediction of Composite Structures Based on Digital Twin with Three Effective Error Correction Strategies