Biodiesel Production through the Transesterification of Non-Edible Plant Oils Using Glycerol Separation Technique with AC High Voltage

Saad S. Almady,Ali I. Moussa,Mohammed M. Deef,Moamen F. Zayed,Saleh M. Al-Sager,Abdulwahed M. Aboukarima

DOI: https://doi.org/10.3390/su16072896

IF: 3.9

2024-03-31

Sustainability

Abstract:The biodiesel industry is a promising field globally, and is expanding significantly and quickly. To create a biodiesel business that is both sustainable and commercially feasible, a number of studies have been conducted on the use of non-edible oils to produce biodiesel. Thus, this study highlights biodiesel synthesis from non-edible plant oils such as pongamia and jatropha using a glycerol separation technique with an AC high voltage method through the transesterification reaction. In this context, non-edible plant oil has emerged as an alternative with a high potential for making the biodiesel process sustainable. Moreover, the study introduces how the created biodiesel fuel behaves when burned in a diesel engine. The results showed that the optimum conditions for creating biodiesel were a temperature of 60 °C, a potassium hydroxide catalyst percentage by weight of oils of 1%, and a stirring time of 60 min at a 5:1 (v/v) ratio of methanol to oil. A high-voltage procedure was used to separate glycerol and biodiesel using two electrodes of copper with different distances between them and different high voltages. The results showed that, for a batch of 15 L, the minimum separating time was 10 min when the distance between the copper electrodes was 2.5 cm, and the high voltage was 15 kV. The density, kinematic viscosity, and flash point of jatropha oil were reduced from 0.920 to 0.881 g/cm3 at 15 °C, from 37.1 to 4.38 cSt at 40 °C, and from 211 to 162 °C, respectively, for the production of biodiesel. Additionally, the density, kinematic viscosity, and flash point of pongamia oil were reduced from 0.924 to 0.888 g/cm3 at 15 °C, from 27.8 to 5.23 cSt at 40 °C, and from 222 to 158 °C, respectively, for the production of biodiesel. The calorific value of jatropha oil was increased from 38.08 to 39.65 MJ/kg for the production of biodiesel, while that of pongamia oil was increased from 36.61 to 36.94 MJ/kg. The cetane number increased from 21 for oil to 50 for biodiesel and from 32 for oil to 52 for jatropha and pongamia biodiesel, respectively. In order to run an air-cooled, single-cylinder, four-stroke diesel engine at full load, the produced biodiesel fuel was blended with diesel fuel at different percentages—10, 20, and 30%—for jatropha and pongamia methyl esters. The produced engine power values were 3.91, 3.69, and 3.29 kW for B10, B20, and B30, respectively, compared with the engine power value of jatropha methyl ester, which was 4.12 kW for diesel fuel (B00); meanwhile, the values were 3.70, 3.36, and 3.07 kW for B10, B20 and B30, respectively, for pongamia methyl ester. The findings suggest that the biodiesel derived from non-edible oils, such as pongamia and jatropha, could be a good alternative to diesel fuel.

environmental sciences,environmental studies,green & sustainable science & technology

What problem does this paper attempt to address?

The main problem that this paper attempts to solve is to produce biodiesel from non - edible vegetable oils (such as neem oil and jatropha oil) by using alternating - current high - voltage technology and optimize the key parameters in its production process. Specifically, the research focuses include:

1. **Optimizing the process conditions for biodiesel production**: Determine the optimal reaction temperature, catalyst dosage, and stirring time to improve the yield and quality of biodiesel. The study found that the optimal conditions are a reaction temperature of 60 °C, a catalyst (potassium hydroxide) weight percentage of 1%, a stirring time of 60 minutes, and a methanol - to - oil ratio of 5:1 (volume ratio).

2. **Using high - voltage alternating current to separate glycerol**: Utilize high - voltage alternating - current technology to accelerate the separation process of glycerol from biodiesel and improve the separation efficiency. The experimental results show that at a high voltage of 15 kV and a copper electrode spacing of 2.5 cm, the minimum separation time for a 15 - L batch is 10 minutes.

3. **Evaluating the physical and chemical properties of biodiesel**: The performance changes of the prepared biodiesel in terms of density, kinematic viscosity, flash point, calorific value, and cetane number were studied. The results show that compared with the original vegetable oils, these properties of biodiesel have been significantly improved. For example, the density of jatropha oil decreased from 0.920 g/cm³ to 0.881 g/cm³, the kinematic viscosity decreased from 37.1 cSt to 4.38 cSt, and the flash point decreased from 211 °C to 162 °C.

4. **Testing the performance of biodiesel in diesel engines**: By mixing different proportions of biodiesel with diesel (10%, 20%, and 30%) and conducting full - load operation tests on a single - cylinder, four - stroke, air - cooled diesel engine, the practical application effects of biodiesel were evaluated. The results show that biodiesel - blended fuels perform well in terms of engine power and can be an effective substitute for diesel.

In conclusion, this paper aims to explore an efficient and sustainable biodiesel production method, especially by optimizing process parameters and introducing high - voltage alternating - current technology to improve the quality and production efficiency of biodiesel, while verifying its feasibility and performance in practical applications.